RV1599REW02 Roper Freezer - Parts

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.

This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.

Sold individually.

Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to give a fresh new look to any handles or areas that have discoloring due to wear. Make sure to clean the area before you begin and wear a pr...Read moreotective mask for safety. Give the can a good shake and spray a few inches away from the surface. Apply the paint until the area is fully covered as desired. Wait until the paint has dried before using the appliance.

This metal freezer door key has a cross shape and is approximately 2 inches long. If your freezer door will not stay shut, you can use the key as a quick fix to keep it closed. If your key will not lock, or unlock the freezer door, check to see if it has been bent or damaged. If the key is damaged, you should look to replace it to avoid d...Read moreamaging the lock. The key should engage the locking mechanism with ease. If the lock sticks when you turn the key, penetrating fluid should be used to loosen the mechanism. These keys are sold separately, and should be stored somewhere safe and not next to the unit.

This is an OEM part that is made of metal and sold individually. The leveling leg is generally used with refrigerators, dryers, freezers, ranges, cooktops, and microwaves. The leveling leg is meant to keep your appliance steady and level to the floor. If you notice your appliance is uneven to the floor it may need to have the leveling leg...Read more replaced. You will notice that the bottom of the leveling leg has a smooth surface to ensure moving your appliance does not require as much effort. This part screws into a pre-drilled hole underneath the appliance.

Sold individually.

Sold individually.

The door gasket is used on vertical freezers. Screws are no longer included with this product. The gasket creates a tight closure around the opening of the door to ensure that outside air does not enter the freezer, causing it to warm up. If you notice that your freezer is not closing properly, is not maintaining the proper temperature, o...Read morer there is frost build up, it could be due to the breakdown of the door gasket. It is white in color. This is an easy repair that should not take longer than 60 minutes and only requires a nutdriver to fix.

The compressor relay and overload kit is an assembly for your refrigerator. The function of the overload is to protect the compressor from overheating by being mounted to the side of the compressor. The purpose of the relay is to boost the compressor. This assembly comes with two smaller plastic pieces that are less than two inches by one...Read more inch. One is black and the other is white. The kit also comes with a red wire tubing. The most common reason for needing to replace the overload and relay is if your fridge is too warm or will not start.

This gate support is designed to support the gate or fence on your vertical freezer. This part is designed for the right-hand side and differs from the left-hand side gate support. Be sure to note which side of your gate support is damaged before ordering this part. This product is sold individually. It is white in color and is made entir...Read moreely of plastic. The gate support is approximately 6.5 inches in length and slightly less than an inch in width. This is an OEM part sourced directly from the manufacturer.

The thermostat sensor barrier covers and insulates the temperature control thermostat capillary tube.