RTT14CBMBRCC General Electric Refrigerator - Instructions

I'm not at all techie, but your site made it easy for me to find the part I needed. The part arrived within 2 days, and walla I installed and all is good.

Thanks, I only wish every internet search was this easy.

The new one not only arrived faster than I expected but it was also a lot sturdier, nice shape and the fridge looks cleaner. Also it offers better support for what I store right on it.

same

First I removed the old cover, and the cans of soda I was using to hold it up. Then I put the new cover in, and snapped it in place. This took less than a minute, and could not have been easier. The replacement cover fits perfectly. Thanks!!

My wife and I followed the installation video & put the gasket in hot water. We struggled to get it started in the second corner on top. Gasket had cooled down so wasn't wanting to go in the slot. I finally got the bright idea to use a hair dryer to warm the gasket as we pushed it along.
That helped us finish the installation.
N ... Read more ot sure the new gasket is the complete answer to the leakage at the top of the door (forming ice crystals). The MAGNETS ARE WEAK compared to my 1 year old GE top freezer refrigerator!
My newer refrigerator "snaps" shut.

pretty easy fix, took out the remaining pieces of cracked cover and handle and replaced the cover and handle (shelf).

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

We thought we would have to replace our frig, but found the part online and it fit perfectly. It's slightly different than the original because it is stronger. All we did was remove the items from the tray, unsnap the broken one and slide the new one into place.

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

I took it right out of the framed box to keep the gasket in shape and snapped it back on the gasket mount on the freezer door it took 5 minutes or less perfect fit

Very easy

I had already ordered a replacement evaporator motor from another vendor. I ordered the evaporator fan blade, compression ring and rubber grommets from PartSelect. Apparently this is a pretty common issue with top-freezer refrigerators. Obtaining these parts and possessing the few tools needed saved me at least $100 over having someone ... Read more else perform the repair. I will further use PartSelect when ordering parts for my other appliances. Thank you.

Replaced above parts and the noise problem was not resolved. Ordered a new motor, fan blade and another set of grommets from PartSelect. The parts were delivered the next day. Took me about 15 minutes to swap the new parts in. It's been 3 days since the repair and the noise has not returned.

after simply replacing shelf, I used the enclosed plactic washers to raise the height of door, so it would clear new shelf. It all worked as planned, thanks

Turn off refrigerator. Remove the plastic air flow cover, styrofoam channel and metal panel inside freezer compartment, remove hex nuts holding motor mount, unplug connector, remove old grommets, remove compression ring, (note 1/4 inch extension of shaft through fan) carefully pull fan blade off motor shaft and put on new motor shaft, le ... Read more aving 1/4 inch of shaft extending through, replace compression ring. If your new fan motor has a female snap connector and the old motor has a male connector (as mine did) you will have to cut the wires on both new and old motors, splice and solder the male connector onto the wires of new motor, wrap carefully with premium electrical tape (or shrink tubing). Replace the 2 grommets, Reconnect the fan and bolt back into place. Make sure all the bolts around the mount are tight. Replace the metal panel. Manually spin the fan making sure it is free of the shroud. If it binds in the shroud, physically move the motor and mount till it rotates freely. Turn on refrigerator and test fan operation. If it's all good, replace the styrofoam and plastic cover.