Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Grate Size
2 of 2 peoplefound this instruction helpful.
Clyde from ALLEGAN, MI
Really Easy
Less than 15 mins
The grates are slightly smaller then the original Kenmore parts and they slide slightly. I purchased a full set of 4 grates - part number PS244182
Was this helpful?
Thank you for voting!
oven racks very old and writing on knobs worn ff
2 of 2 peoplefound this instruction helpful.
Patricia from SAN JOSE, CA
Very Easy
Less than 15 mins
Very was ti replace racks and knobs. Very fast mail service
Was this helpful?
Thank you for voting!
Broken drawer glider
2 of 2 peoplefound this instruction helpful.
James from RANCHO MIRAGE, CA
Very Easy
Less than 15 mins
Screw drivers
Took off broken part and replaced it with the new part by removing a Phillips head screw, the broken part, replace with new and reinstalling the same screw.
Was this helpful?
Thank you for voting!
lights blown out
6 of 14 peoplefound this instruction helpful.
Gerald from WINTERVILLE, GA
Very Easy
Less than 15 mins
replaced lights in refrigirator and freezer
Was this helpful?
Thank you for voting!
Existing oven bottom was damaged.
2 of 2 peoplefound this instruction helpful.
Charlotte from CHICAGO, IL
Really Easy
30 - 60 mins
Nutdriver
Removed two screws to remove old bottom. Insert new oven bottom and re-attach screws.
Was this helpful?
Thank you for voting!
Broken button behind overlay
1 personfound this instruction helpful.
Frederick from MAYSVILLE, NC
Really Easy
30 - 60 mins
Nutdriver, Pliers, Screw drivers
Remove both over and control panel and replace both
Was this helpful?
Thank you for voting!
BASE OF BULB BROKE OFF & WELDED TO SOCKET
1 personfound this instruction helpful.
NEIL from ROCKY POINT, NY
Easy
30 - 60 mins
Nutdriver, Pliers
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this helpful?
Thank you for voting!
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
1 personfound this instruction helpful.
Dana from LEEDS, AL
Really Easy
More than 2 hours
Pliers
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Was this helpful?
Thank you for voting!
Removal reinstalling
1 personfound this instruction helpful.
Thomas from HAMPSTEAD, NH
A Bit Difficult
More than 2 hours
Screw drivers, Socket set
Removal old fashioned oven door handle took time after removing the oven door. New replacement handle was easy to install! Try to reinstall was long and finally got installed after 5 attempts due hinge on right side issue
Was this helpful?
Thank you for voting!
finish on old oven bottom was damaged
1 personfound this instruction helpful.
ERNEST from MANCHESTER, NJ
Very Easy
Less than 15 mins
Screw drivers
Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie
Was this helpful?
Thank you for voting!
Only A "Cosmetic" Replacement.
1 personfound this instruction helpful.
Jimmy from Bonifay, FL
Really Easy
Less than 15 mins
No job here. . . . Just sat new parts on to replace old ugly parts.
1. Open oven door 2. insert oven racks (perfect fit) 3. close oven door. Done and finished - man am I tired
Was this helpful?
Thank you for voting!
The light inside the oven had burned out
3 of 7 peoplefound this instruction helpful.
Catherine from SEATTLE, WA
Very Easy
Less than 15 mins
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot. 1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back. 2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place. 4. Put the cap back. 5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Read less
Was this helpful?
Thank you for voting!
Oven bottom badly marred after 16 years.
1 personfound this instruction helpful.
Charlie from NAPLES, FL
Very Easy
Less than 15 mins
Screw drivers
Two set screws in rear; removed easily with a screwdriver. Old oven floor lifted out easily; new oven floor dropped in just as easily; set screws re-installed. Done. Pleasantly surprised at how easy this went.
Was this helpful?
Thank you for voting!
replace burner pans
1 of 2 peoplefound this instruction helpful.
roland from oak creek, WI
Really Easy
Less than 15 mins
take off top grates,place new one's in time 20 sec.
My Orders
