RF764005 Hotpoint Range - Instructions

Frank from Canyon Country, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

replacing old rusted drip pans w/ rings

simply lifted the heat coil and slid the rings off and lifted the drip pans off. Vacumed the bottom underneath the old pans. Cleaned the grease off around the stove where the rings sat. Let it dry and added the new rings and pans. Looks like it did 30 years ago.......let them try making a stove last that long today !! Make sure the power is OFF at the electrical box.

Parts Used:

steven from peabody, MA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Stove element not working

The only hard part of the job is removing the old, corroded terminal block. Be careful not to break the electrical wire. Other than that, just sand the contacts and reassemble. This is the second one I have replace on my 4 burner stove. 2 more to go.

Parts Used:

Terminal Block Assembly

dennis from redding, CT
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

The control knob stem broke off when I moved the stove.

I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.

Parts Used:

Range Infinite Heat Switch Kit

Jonathan from Harvard, MA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

3 of 10 people found this instruction helpful.

Was this instruction helpful to you?

burners were burnt

replaced

Parts Used:

John from Brookhaven, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Old and corrosive due to age

After receiving parts, was getting rims unpackaged and removing the old rims, then and installing the new ones. Extremely easy to do. No tools needed

Parts Used:

Donald from McConnells, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Original parts lost or discarded by prvious owner

Just replaced drip pans and rings on stove

Parts Used:

Steven from West Melburn, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Both 8 inch surface units burned out

Simply unplug old unit and plug in the new. Easy

Parts Used:

Catherine from Corinna, ME
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Element was no longer heating up

I turned off the circut breaker and disconnected the old terminal block - some difficulty removing the wires because of corrsion - I was able to reconnect the wires to the new block quickly and I was done - fast and easy - so happy to have found the part so easily with your program. Thank you

Parts Used:

Terminal Block Assembly

Robin from Garden City, NY
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers, Wrench set

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

needed to replace drip bowl and trim ring

The replacement drip bowl and trim ring fit perfectly.

Parts Used:

Stephanie from Kitty Hawk, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

replaced trim rings and drip pans

Simple replacement on an old "built in" range in good condition but drip pans and trim rings soiled beyond cleaning. Stove top, although 20+ years old, now looks like new. So glad to find parts were still available as "universal" replacement parts for the 8 inch burner do not fit. Delivered to my door in days.

Parts Used:

Louise from Wesley Chapel, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Old Burner was crappin' out after 20 years of service

Pulled out the old burner that was held in by a metal spring clamp. Pushed the new one in.

Good as new.

Parts Used:

Jay from Madison, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

The old surface unit was not generating heat

We just remove the old surface unit and insert the new one by hand. Thanks to PartSelect, we were able to buy really good quality part that works right away! It was a 26-year-OLD GE Stove/Microwave space maker, the parts were hard to find in stores. Thank you for selling this! All the best for your business!

Parts Used:

Yi from Miami, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Element burned out

Partselect had the right part, clearly indicated in the diagrams and menus. Shipped quickly. Easy to use web site.

Parts Used:

J. from Durham, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Old drip bowls could not be cleaned

Replaced drip bowls.

Parts Used: