Keep the center door flap moving smoothly with this replacement spring for select French door refrigerators. The spring adds tension so the flap opens and closes as the doors move. Replace it if the flap stays open, blocks the door, or makes a rattling sound. Unplug the refrigerator before starting the repair. Check the exact appliance model number before ordering.
When the folding divider on a French-door refrigerator will not retract, the spring pin or sleeve may be worn or broken. This support piece helps hold the mullion spring in the left door so the flap moves as the doors open and close. Check for a missing spring, cracked hinge point, bent flap, or door alignment problem before choosing a re...Read moreplacement. Confirm fit with the full appliance model because small sleeves can differ. Record the spring position before removal and avoid forcing brittle plastic. Install the sleeve in the same direction shown in the service diagram, reconnect the spring carefully, and test the flap before loading the door with food.
This screw, known as a handle fixer, is used to keep the door handles on your refrigerator secure. This screw is a genuine OEM part that comes individually, and simply screws into place in your refrigerator, and then allows the refrigerator handle to slide onto it. Your refrigerator normally has two of these fixer screws, so be sure to check how many you require before ordering.
This a genuine OEM temperature sensor, designed for use with refrigerators, and is an individual part. This temperature sensor is responsible for detecting and adjusting the temperature in your refrigerator. If your refrigerator is having issues with being either too cold, or too warm, it is likely that this sensor needs to be replaced. T...Read moreo replace it, ensure that your refrigerator is turned off before you locate it with your user manual and replace it.
This evaporator fan motor is in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated. When the evaporator fan motor fails, it often generates a lot of noise in the freezer area. If you notice that your refrigerator or freezer is noisy, or is not ...Read morecooling like it should, you may need to replace the evaporator fan motor. The base of this part is approximately 3 inches in length and 2 inches in width. The shaft of this part is an additional 2 inches in length.
This is the end cap for the freezer door of various Samsung refrigerators. This end cap is made of plastic and features a brushed-metal finish, and simply snaps on or off the end of the freezer door handle. If your freezer door handle is missing its end caps, or if they are damaged, they should be replaced to give your door handle a more ...Read morefinished appearance. Most handles require two end caps, so be sure to consider how many end caps you require before ordering.
This ice maker assembly in your bottom-freezer refrigerator automatically produces and dispense ice. It consists of a mold for 9 ice cubes, a control device, and a 12-pin wiring connection and housing. Its dimensions are approximately 4-1/2 inches by 12-3/4 inches by 4-1/4 inches, and it can produce about 84 ice cubes within 24 hours. Thi...Read mores genuine OEM assembly is sold separately from the water line and the water inlet valve.
This is a power cord made for Samsung refrigerators. If your current power cord is damaged, broken, or no longer supplying power to your fridge, you can disconnect it from the wall outlet, strip it from your fridge, and replace it with this OEM cord. This power cord is sold individually and does not include any other parts or accessories.
This refrigerator door handle is a genuine OEM replacement part that is designed for Samsung freezers. The silver handle is made from high-strength aluminum alloy and coating. It is attached to the outer panel of the freezer where it allows for easy opening and closing of the freezer door. It has an ergonomic design that allows users to e...Read moreasily grip and pull the door to access the contents of the freezer. It is recommended to replace the handle if it is cracked, broken, unstable, or if its appearance has deteriorated.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Evaporator frozen (refrigrator section) and allowing top section to lose cooling
107 of 181 peoplefound this instruction helpful.
Richard from GULFPORT, MS
Easy
30 - 60 mins
Screw drivers
This is the Samsung French door refrigerator style that so many people have complained about freezing up and not cooling the top section. I first changed out the defrost thermostat and this did not correct the problem. I done a quick resistance check on the temp sensor that's mounted on the evaporator itself. The resistance would change w
... Read morehen holding an ice cube on the sensor so I just assumed it was ok. PLEASE TAKE NOTE: When performing a resistance check on this sensor, make sure your readings match the Samsung temp/resistance chart in their literature. My sensor was way off calibration and was causing the freeze up. Its working as designed now and DW is happy again. Learn from my mistake.
Read less
Was this helpful?
Thank you for voting!
Left side French Door flap on Samsung refrigerator didn't retract when closing.
51 of 70 peoplefound this instruction helpful.
HOLLIE from FORT WAYNE, IN
Very Easy
Less than 15 mins
OMG seriously! I stopped into my go-to appliance repair shop to ask about what might be needed to repair the problem with my refrigerator door. They said you will need to replace the Mullion Flap piece. Cost would be $250-300 with part, labor and service. I went on line to see if I could handle the repair process myself. I found a How to
... Read more - U Tube video and turns out I only needed to replace a little spring and pin not the whole Mullion Flap. Went to Parts select, ordered the spring and pin and did the repair myself in about 5 minutes. Shipping was $7 so I ended up paying $13 total.
The installation video notes that the door mullion spring has a bent end, and that the bent end of the spring is to be inserted into the LOWER hinge. However, on my refrigerator door, the bent end of the door mullion spring must be inserted into the UPPER hinge in order for the door to function properly. (Also noted that in your video t
... Read morehe installer manually closed the door mullion rather than just closing the refrigerator door, another indication that the installation of the spring was incorrect.) After watching the video several times to confirm I was installing the door mullion spring according to the video instructions, I tried inserting the bent end of the door mullion spring into the upper hinge, which proved to be the correct installation of the door mull spring. What should have been a 5 minute repair turned into an ½ hour repair.