The ice maker cube tray holds the water that comes from the ice maker during the process of it becoming ice. This part is white in color and made of plastic. All you will need for this repair is a flat blade screwdriver. Over time, the tray may bend out of shape or mineral deposits build up inside, which makes the ice stick to the tray. Y...Read moreou will find the ice maker underneath the ice bin in the freezer. Use your flat-head screwdriver to release the tab holding the ice maker in place, this will expose the ice tray.
This is a 40W/120V ice maker assembly for your refrigerator. Ice maker assemblies are designed to continuously make ice cubes by supplying water through its valve, freezing it, and then ejecting the cubs into the ice bin. This ice maker assembly is made of plastic and measures approximately 12 inches, long by 4.75 inches tall and 4.5 inch...Read morees wide. This ice maker is an OEM part that does not come with any other installation parts and attaches within the freezer compartment via its single wire harness.
This evaporator fan motor is sourced from the original manufacturer for use in refrigerators. It circulates cold air throughout the refrigerator compartment to maintain consistent cooling. If the evaporator fan motor is faulty, you will notice inconsistent internal temperatures, excessive and unusual noise, and frost build up. To begin th...Read moree repair, disconnect the refrigerator from power and remove all shelves and food items in front of the rear panel. Remove the mounting screws on the rear panel and carefully detach it to expose the fan motor. Disconnect the wire connectors to the motor and pull it out of the refrigerator. You may reuse the old fan blades if they are in good condition. Insert the new motor in the refrigerator and reattach the mounting screws. Reconnect the wire connector and reassemble the refrigerator in reverse order.
The Samsung Defrost Sensor (DA32-10105R) is a genuine part designed specifically for Samsung refrigerators. This sensor, sometimes referred to as a defrost thermostat or defrost temperature sensor, is an integral part of your refrigerator's defrost system.
This sensor cover, also known as the ice maker thermostat cover, is a genuine OEM replacement part for Samsung refrigerators. It is made of durable white plastic and has measurements of approximately 2.25 inches by 1 inch. The sensor cover is responsible for protecting the ice maker thermostat from contaminants, ice build-up, water, and m...Read moreoisture which can prevent the thermostat from regulating the ice maker temperature properly. If your ice maker is producing ice very slowly and you also notice large clumps of ice in the ice tub, then the sensor cover is likely damaged, or it has fallen out of place. You will need to remove the freezer drawers to replace this part.
This condenser fan blade (part number DA31-00010D) is for refrigerators. Condenser fan blade DA31-00010D moves air across the condenser coil to cool the hot refrigerant before it enters the evaporator. Safely store any food that could deteriorate while the power is off and unplug the refrigerator before installing this part.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice Build up behind refrigerator internal panel
5 of 7 peoplefound this instruction helpful.
David from WILMINGTON, DE
Really Easy
More than 2 hours
Pliers, Screw drivers
I performed the repair to my own refrigerator, after watching multiple YouTube videos. I installed a secondary heater for the defrost coils and replaced the defrost sensor. The defrost sensor was actually bad. Today, 1/27/2024 I rechecked the fix from last week. All seems to be good so far.
If I get any build up of any ice on t
... Read morehe bottom tray of the recessed panel where the drain port is located. I suspect I will also need a new Defrost Heater as well. For now the refrigerator is operating as expected. There is a small amount of ice build up as of today.
Also, I had recently replaced the drain tubes, added a longer heater element part to fit the drain hole, and cleaned the fins in the back of the refrigerator. Thank you.
Read less
Was this helpful?
Thank you for voting!
Fridge side no longer cooled, freezer still workekd fine.
3 of 5 peoplefound this instruction helpful.
Roger from Belle Fourche, SD
Easy
1- 2 hours
Screw drivers
A couple of blogs said the freezer defrost sensor should be replaced, so I ordered one. Did not fix it. I did, however find a service manual online and one of the blog sites and it showed me how to remove the inside duct work. I discovered the fan the recirculates the air across the evaporator coil was not working. Ordered a new fan mo
... Read moretor and installed it, fridge works perfectly now.
Read less
Was this helpful?
Thank you for voting!
The ice maker was overflowing and freezing over
2 of 6 peoplefound this instruction helpful.
Paul from Streator, IL
Really Easy
30 - 60 mins
Socket set, Wrench set
I watched several repair videos and decided I could do this because I have been doing mechanical work for over fifty years.The videos convinced me it needed replaced it is a 2009 model I bought new. I ordered the new part from parts select it came in 3 or 4 days.The hardest part was removing the freezer door and reinstalling when I was do
... Read morene.That wasn’t complicated just awkward.Removing the ice maker was simple and replacing it with the new one was easy.There was a protective plate on the front of the old one that wouldn’t fit on the new one.So I left it off.So far it has been working very well.