PVM9215SK3SS General Electric Range - Instructions

opened the door and put in the tray!

Removed 6 screws from the front and back of the bottom of the unit. 3 screws each side. The panel will swing down. Remove the wires from the motor. Remove the one screw from the old
motor. Insert the new motor and reverse the procedure.
DIY will save you a $ 95.00 GE repairman labor bill, plus the cost of the motor. I repai ... Read more red the problem for less than $25.00!

This is sometimes described in other repair notes as "microwave 'runs' when door is open."
With power disconnected: Remove the microwave's metal grill surround. Three lower screws accessible with lower oven door open. Two screws accessible at top of microwave door opening with door open.
Remove microwave control panel: Remove t ... Read more wo femaleTorx head screws (#27?) that secure the panel, accessible at right side of door opening. The right side of the control panel is secured by plastic tabs fitting into slots in the oven frame. Take good care to note how these tabs disengage from the slots (lift and shift). Tab breakage very possible! Once disengaged, the panel hinges outward and downward and is self-supported. It may be necessary to guide some of the wiring out of the way to fully lower.
There are three door switches, one "monitor" and two "secondary" switches. All switches are housed in a plastic frame, which must be lifted out of position for access, each switch is retained by flexible plastic, breakable-looking hooked fingers. Also note that the electrical connectors have tiny release tabs that must be depressed in order to pull them off of the switches. In my case the topmost switch, one of the "secondary" switches, was clearly bad since there was no "snap" or click when pressing the switch's button. Maybe you can determine which switch is bad before proceeding but I had ordered all three to avoid going through this exercise again any time soon.
Replace switch or switches, place switch carrier back into position and otherwise reverse the disassembly steps.

Most of the effort is simply getting the oven out of the built in enclosure and the sheet metal off. This take about 15 minutes then you have to remove the two screws (not handy location) that hold the door latch/switch assembly so you can remove the switch. I did this BEFORE ordering so I could test the switch (it was charred) and veri ... Read more fy the part needed. WATCH OUT - some ovens use a normally open an some a normally closed version of this switch - you have to get the right one. I checked several suppliers that were showing the WRONG switch for my model. PartSelect had it right. Once I received the switch I had it on and the oven installed and running in less than 30 miutes. Working fine since then...

Ordered through parts.select because GEprice was totally outrageous.
Unfortunately, my first order was lost and after 2 weeks I phoned your customer service and Betty was quite helpful. She followed up (as I called on a Saturday am) on Monday and reported to me that the item was lost. She then asked me if I wished to place anoth ... Read more er order. I did, of course - it arrived in a timely manner - I placed the cooking tray into the microwave and I was in business!!! Thank You Partselect!!!!!

I replaced the switch at the bottom per instruction. I had both switches. I think it was the monitor door switch.It works fine now. Thank you Part Select .

Took the front panel off, played with the switch while it was plugged in to verify the switch was bad. I actually was able to tweak the switch just right to keep the microwave working while the part was being delivered. When it came it was just removing two small screws and replacing. Very easy.

Open the box that the part came in and place it in the microwave. The best is how fast it came to my home. Thanks

The new turntable shipment was super fast!!! I received it only a few days after ordering it. Installation was nothing more than placing it in the microwave oven.

GREAT Transaction!!! Thanjs!!!

I took the cover off, and replaced the glass-- the difficult part, was ordering the glass..on the list of parts to order-- the description of the glass was mis-leading

just set the glass turntable in and bingo it worked
no tools needed. thanks for such a fast delivery
sincerly dennis and chris delbello

Unscrewed numerous screws holding the "body/shell" to the microwave. Removed body. I then unplugged top door switch, replaced it with new one, and "tested" the new one. I fixed our $400 convection micro with an $18 switch. NICE!

I took the cabinet off and saw where the switch had been burnt. So I remove it and order another one from your company. And I put new clips on it with heat shrinks. We might get another 30 years out it, Although I'm 80 years old.

Followed the online videos to enter the cavity to the switch holder. Noticed right away the dreaded capacitor was in back right corner behind where the touch pad had been removed. I isolated the capacitor with an old computer mouse pad for extra safety. Took some manipulations to get the switch mount out from behind the wire bundles. Once ... Read more out front, easy to use small flat blade screwdriver to release each switch and replace with matching new switch. Only one switch was bad but replaced all three. Back together and working great.

Removed the outer cover to access the door switches. Turns out there were three switches, but I determined that only two were bad. When the small colored tab on the switch is pushed in it should make a clicking sound. The two bad switches had no resistance and did not make any noise when pressed. Removing the switch is relatively easy, ... Read more you simply pull it away from a couple small tabs holding them in place. After reconnecting the wire leads, insert back into the holding tabs and install the cover.