PVM1870DM2CC General Electric Microwave - Instructions

damper plate was a snap-in part. rotated fan discharge to top of microwave. installed ducting to discharge food odors outside.

Lifted off the glass turn table and just pushed the new plastic couple onto the drive post. The plastic coupler is splined, so just sit it onto the drive post and lightly turn it until it starts to drop and give a little downward push. That's it - about 30 seconds and the table is turning again.

When we moved into our recently purchased home, I noticed that the turntable in the microwave wasn't turning. I discovered that the coupler was missing and hoped that nothing else was damaged and that getting a new one would fix the problem. I ordered the part and it came the very next day, even though I got 3-5 day shipping. Didn't even have to unscrew anything to install it. It popped right in and the turntable works perfectly now.

Installation of the damper was effortless but removing the microwave, cutting holes vertically through an overhead cabinet then installing ducting with a ninety degree bend, through another cabinet, and then through outside wall consumed most of the time and effort.Your service, packaging, and timely (next day!) were extremely helpful.

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.

Microwave would not turn on. Lights and fan worked fine. Before the microwave stopped completely, it would turn the microware fan on even when door was open. I read the reviews and they were exactly the same issue that others were facing. Once I opened the front panel and got to the switches it was easy to figure out which switch was bad as it was the one that was soft (When clicking it). It was hard to take it out though (it seemed stuck). So, I used a plier to yank it out. I put in the new switch and everything worked just great! I would like to thank other comments that were left on the site to make my task much easier. Thank you (to the commenters on PartsSelect), you not only saved me money, but also ensured that I learn about the microwave more and give me the confidence that I could fix it.

Once we figued out that you had to remove the panel underneath the microwave, pull down the turntable motor part and then insert to coupler it went really fast. Through trial and error we figured it out, but should have checked for installation instructions on the internet. Repair time would have been less than 15 minutes.

bought a fuse but that didn't solve the problem. Guess I need a new microwave

Turn off main power bracker. Removed fan vent, removed control panel, disconnect leads to the three monitor switches. Replaced the secondary switch (top). Reversed procedures.

Pull cover off , located the bad magnetron . Then replaced it with the new one. About 15 min. Of work.

First, unplug microwave. Unscrew two screws at top of microwave, slide grill cover left and remove. This allows access to single screw holding control panel. Remove this screw and lift up control panel to remove. Secondary door switch is black switch at lowest position. The switch is held in place by a lever in back and very hard to get to. Remove the wires plugged into the switch, then remove two screws holding the plastic switch mount that holds all three switches. These screws use a "star" type screwdriver. Once the plastic mount is free, lift it up, right, and tip it slightly to find the lever that will release the black secondary door switch (the lowest switch)...release the broken switch, snap the new switch in its place. Replace the plastic mount by lifting and replacing back into position and replace the two "star" screws. Now, replace the wires onto the new switch, and test operation. Replace control panel, and top grill. It goes faster than it writes...getting the old switch out through that difficult to reach lever was the hardest part...still less than thirty minutes.

At first I thought it was just the bulb, but I wasn't able to find a video of the exact model. The dificult part was figuring out how the vent housing came off (turns out it slid to the left then lifted out) but after I figured that out, replacing the cable assembly and the bulb was really easy.

it was a simple screw in on both ends. no soldering

Simple install. Thanks for your prompt response to my order and interest.

removed housing. saw t-stat was burnt. replaced t-stat by removing mounting screw and installing new t-stat. reinstalled mounting screw. reinstalled oven housing. 15 minute job.