PSCS3RGXCFSS General Electric Refrigerator - Parts

This compression ring is meant to hold the evaporator fan motor in place in the freezer compartment of your refrigerator. This is is a genuine OEM part. The tools needed to complete this repair are a Phillips screw driver and small flat blade screw driver. Be sure to turn off your refrigerator before removing the evaporator fan cover so t...Read morehe fan does not turn on during repair. It is recommended to check the grommets, evaporator fan, and fan blades during repair in case they also need replacning. The compression ring may need replacing if the fan is noisy, or the refrigerator compartments are too warm. This part is sold individually.

This tank stores water until the water actuator is activated and water is requested.

The lid bumper or evaporator fan motor bumper in your refrigerator prevents the fan motor from scraping against the side bracket. If your refrigerator/freezer is noisy, the bumper could be worn down or missing, and the sound could be a result of the motor scraping the side bracket. You will find it between the fan motor and the side brack...Read moreet on the evaporator fan motor assembly. To access the bumper, you will need to remove the evaporator fan motor assembly from the freezer. This part is made of orange rubber and is less than half an inch in diameter. It has a rounded top and a slightly pointed bottom, and is sold individually.

This crank door recess is supplied directly from the original equipment manufacturer. The plastic part is fastened behind the interface dispenser assembly in the freezer door. Activated by the dispenser solenoid, this part regulates the opening and closing of the ice chute door. A screwdriver is needed for the repair. The crank door recess is sold individually.

This OEM water filter works with side-by-side and bottom freezer refrigerators. You will find this filter mounted in a vertical position in the back upper right-hand corner of the refrigerator compartment. If your model does not have an indicator light, remember to use the month and year stickers on the new cartridge to remind yourself to...Read more replace it in another 6 months. Replacement timelines can vary according to your local water conditions. To install the new filter, you will first match the threads with the corresponding threads on the holder. Position the top of the new cartridge up into the holder without pushing it upward. Carefully turn it to the right until it will no longer turn. Make sure you run water through the dispenser right after installation. This clears the system and prevents sputtering. If you have an LCD model, press the Filter Replaced button to reset. If you have a non-LCD model, press and hold the Reset Water Filter button on the dispenser for a few seconds. This filter filters down to 0.5-1 microns. The lower the micron the more toxins are caught and lessened.

This evaporator fan blade is for your refrigerator, and it circulates air so that the temperature of the fridge is regulated. This model has 3 blades, and is a little more than 4 inches in diameter. It is made of white plastic and is sold individually. If your refrigerator is noisy and you hear a clicking sound, it is a good indication th...Read moreat the evaporator fan blade is warped or damaged. If the fridge or freezer sections become too warm, the fan could be to blame as well.

Sold individually.

The shelf stop in your refrigerator is what locks the shelf into the refrigerator liner. The shelf stop can be found attached to the shelf. To remove the shelf stop, begin pulling the shelf out until the stop hits the refrigerator liner, then depress the shelf stop to remove the shelf. With the shelf removed, you can simply slide the old ...Read morestop out of its groove, and replace it with a new one. This part is made of white plastic and is about 1 inch in length. It is sold individually, and is an OEM part sourced directly from the manufacturer.

This part is the replacement water line for your refrigerator. It is a long plastic tube, which is 5/16 of an inch in diameter. If your refrigerator is leaking, or will not dispense water or ice, you may have a damaged water line. When you replace the water line, you may want to pick up a new water tube union as well. You can use a utilit...Read morey knife to cut the old water line where it is damaged, and use the union to attach the new water line to the old one. This tubing is sold individually and is an OEM part.

This part strips the ice from the icemaker mold during the ejection cycle. Used on rear mount icemakers.

Coarse thread

This part is a replacement pan cover gasket for your refrigerator. You will find the pan cover gasket on the meat pan, and it helps to seal the pan. If the pan cover gasket is lost or damaged, it will not be able to create the seal and will need to be replaced. The gasket is approximately 15 inches wide and is white in color. It is an OEM part from the manufacturer and is sold individually.