PP28PDT ((967288702)(2014-09)) Poulan Pole Saw - Parts

It is a genuine component that is supplied by the original manufacturer to use for a Husqvarna trimmers. This part is made of steel and hard plastic. This part includes the drive pulley, rewind pulley, recoil spring and a drive spring. If the engine does not start, has a hard time starting or the pull rope does not retract then it is tim...Read moree to replace this part. Before replacing this part, please make sure the engine is cooled and you remove the wire and boot from the spark plug to avoid the engine by starting.

This OEM bar adjustment retainer is a metal component that securely holds the adjustment screw and pin in place, allowing you to adjust the chain tension. It is typically located near the front of the chainsaw, close to the guide bar. If the guide bar is over-pressured, the retainer can become stressed and fail, causing it to ride up on t...Read morehe screw. Signs of a damaged retainer include visible breaks or deformations. You may also have trouble in tightening or loosening the chain, as the screw may become loose during adjustment. To remove a faulty retainer, remove the side cover by loosening the nuts and the tension screw on it with a socket. Unscrew the guide bar and replace the damaged retainer. When installing the new retainer, ensure the cone points towards the adjustment pin. Please note that the replacement retainer is sold separately from the guide bar and adjustment pin.

This is a genuine OEM sourced replacement part designed for use with Poulan and Husqvarna handheld lawn and garden equipment. This is a standard hardware which has multiple applications based on your unit. Please make sure to check appropriate diagrams for correct location and use of this item. Please note, one torx screw is included per order.

This is a Manufacturer Approved replacement part designed for use with Gas Pole Pruners. Bar holds the cutting chain in place. If it is bent or worn out, causing the chain to not cut properly the bar should be replaced. It is made out of Metal and it is Sold Individually. You would need a Hex Keyand a Wrench to replace this part. • Re...Read moremove the housing • Release the chain tension • Remove the chain and the tensioner • Remove the bar and replace it with a new one • Secure the tensioner and the chain • Reassemble the housing and tighten the chain

It is an authentic OEM supplied replacement part that is specially produced for Husqvarna handheld lawn and garden equipment. The ignition module also known as an armature-magneto provides electric current for the ignition system sending pulses of high voltage to the spark plug. The primary symptoms of a faulty module usually would be dif...Read moreficulty starting your equipment or inability to start it at all. It is made from durable metal with a rubber insulated wire and a spark plug boot. Please note this part is sold individually.

This is an authentic Husqvarna replacement part manufactured for use with trimmers and brush cutters. The carburetor adapter is used to connect the carburetor to the cylinder. The carburetor adapter is available as an individual replacement part, please note the gaskets are available separately.

This genuine replacement coupler is sourced from the original manufacturer and is designed for use with trimmers from Poulan and Husqvarna. It connects the upper and lower sections of the drive shaft assembly, ensuring a secure and stable link for proper power transmission. Ideal for routine maintenance or repairs, this coupler is sold individually and is built to meet OEM standards for fit and performance.

This is an original replacement part manufactured for use with trimmers. The special bolt is used to fasten the muffler to the cylinder. A hex key is required to install the bolt, and it is sold individually.

This is a genuine manufacturer-sourced replacement part which is specially designed for use with Poulan and Husqvarna lawn and garden equipment. It is a standard hardware which has multiple applications, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this screw. Keep in mind this high-quality item is made of durable metal and is sold individually.

This replacement screw is a high quality hardware that is designed for use with Paramount, Poulan and Weed Eater power equipment. It has multiple applications depending on your equipment, please make sure to check appropriate diagrams for correct location and use of this item. One durable hex socket head screw is included per order.

This is a genuine OEM sourced replacement part that is intended to be used with trimmers and brushcutters from Husqvarna and Jonsered. The spark arrestor attaches to the outside of the muffler over the exhaust port. This kit is used to prevent flammable material from exiting the muffler with the exhaust gasses. The spark arrestor kit is priced as a single item.

This is a genuine replacement part for Craftsman chainsaws. The bar bolt is designed to sit behind the bar mounting plate and gives a location for the bar to fasten to. The bolt is made from high-quality metal. Note you require two bolts to fasten the bar. This item is sold individually.