PP255 Poulan Chainsaw - Parts

This is an authentic Craftsman replacement part, sourced from the original manufacturer for use with chainsaws. The special pulley is used to house the starter rope and support the starter spring. This pulley is available as an individual replacement part, please see model diagram for associative parts.

This is an original replacement part manufactured for use with chainsaws and leaf blowers. The washer is commonly used to disperse the pressure put on the flywheel by a nut across a wider surface area. This washer is available as an individual replacement part, please see model diagram for associative parts.

This authentic manufacturer-supplied seal is specially made for use with Poulan, Husqvarna and Jonsered chainsaws. It is a special hardware that helps to provide a tight fit between connected parts. This is an identical replacement for a missing or a worn seal that was installed on a new unit. Make sure to refer to the appropriate diagram...Read mores for your model to ensure the exact location and the correct application of this component. This high-quality seal is made of durable material and is sold as an individual item. A wrench set will be needed to perform this repair.

It is a genuine item is supplied by the original manufacturer for use with Poulan, Jonsered and Husqvarna chainsaws. This plunger and gear assembly functions as an oil pump that helps to lubricate the chain. Unfortunately, over time components may wear out or get damaged eventually seizing operation and requiring a replacement. This high-...Read morequality assembly consists of a durable plastic housing and a metal plunger with a gear. Refer to the owners manual and the diagrams of your model for the correct application of this assembly. You will need a screwdriver and a wrench set to perform this repair.

This authentic manufacturer-sourced component is specially designed for Poulan and Husqvarna gas-powered chainsaws. It is an identical replacement for a missing or a damaged retainer that is utilized to secure the piston pin. To ensure the exact location and the correct application of this product, refer to the appropriate diagrams for yo...Read moreur specific model. Keep in mind this high-quality hardware is made of durable metal and is sold as an individual item.

This is an authentic spur sprocket produced by original manufacturer. It is compatible with a variety of Husqvarna and Poulan chainsaws. A sprocket drives the chainsaw\'s chain component. This part is replaced regularly due to normal wear. Sold individually.

This is a genuine Husqvarna, Poulan, and Jonsered replacement part used in compatible chainsaws. The fuel tank vent attaches to the crankcase and helps air to flow into the tank. No tools should be needed when replacing this part. It may become broken and will need to be replaced. This part is available as an individual replacement part.

It is an OEM part which is made for use with Poulan and Husqvarna chainsaws. This is the special seal which helps to supply the oil. If the part is missing or is damaged, this will provide an identical replacement for the original component that was installed on a new unit. Check the appropriate diagrams for your model to ensure the prope...Read morer repair procedure. One durable rubber oil seal is included. A screwdriver and a wrench set will be needed to take the housing apart.

This is an authentic OEM part for use with Poulan Chainsaws. The throttle cable assembly controls the engine speed. The most common reasons for replacing the throttle cable is if the throttle is not functioning, there is no tension in the throttle lever, the throttle cable is loose in the housing, the throttle cable is disconnected or the...Read more throttle cable linkage (on ends) are broken. This part is sold individually. The tools that you will need to replace the throttle cable is a Torx / Phillip's drivers and a Standard screwdriver.

This is a genuine OEM part from Husqvarna. The intake sleeve is made of durable plastic, and is compatible with many chainsaw models. This component is designed to secure the air filter onto the chainsaw carburetor. The intake sleeve is sold individually. For the installation, you will need a screwdriver, hex key and a wrench.

This is a genuine Craftsman replacement part designed for use with chainsaws. The choke lever is used to adjust the choke to restrict or allow more airflow in the chainsaw. The item is made of durable plastic. This item is sold individually.

This is an authentic OEM sourced component which is made for use with Poulan, Husqvarna and Jonsered chainsaws. It is a special bolt that helps to secure the bar. Refer to the parts diagrams of your model for the exact location and the correct installation. Note, this high-quality bolt is made of durable metal and is sold individually. Yo...Read moreu will need a wrench to secure or remove it. Keep in mind the #530015917 Nut - Bar Mounting is sold separately.