PP255 Poulan Chainsaw - Parts

This OEM bar adjustment retainer is a metal component that securely holds the adjustment screw and pin in place, allowing you to adjust the chain tension. It is typically located near the front of the chainsaw, close to the guide bar. If the guide bar is over-pressured, the retainer can become stressed and fail, causing it to ride up on t...Read morehe screw. Signs of a damaged retainer include visible breaks or deformations. You may also have trouble in tightening or loosening the chain, as the screw may become loose during adjustment. To remove a faulty retainer, remove the side cover by loosening the nuts and the tension screw on it with a socket. Unscrew the guide bar and replace the damaged retainer. When installing the new retainer, ensure the cone points towards the adjustment pin. Please note that the replacement retainer is sold separately from the guide bar and adjustment pin.

This is a standard hardware which has multiple applications based on your tool. It is sourced from original equipment manufacturer for use with a variety of power equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. Requires a hex key or an allen wrench to install or remove it.

It is a genuine item that is supplied by the original manufacturer for use with Poulan and Weed Eater chainsaws. This washer-clutch is a special friction disk that helps to engage the clutch by ensuring a right fit between connected components. It provides an identical replacement for a damaged or a missing hardware that was installed on ...Read morea new unit. Check the diagrams of your model for the exact location and the correct installation of this part. One durable metal washer-clutch is included. You may need a screwdriver and a wrench set to perform this repair.

This is an authentic item sourced from original manufacturer. If the chainsaw bar doesn't adjust when you turn the tension screw usually the tension gear/pin or the adjustment bolt is worn or damaged. This part is made out of metal and it is sold individually. You would need a phillips head screwdriver to remove or secure this screw.

This replacement carburetor gasket is specially made for use with gas chainsaws. It is supplied directly from original equipment manufacturer. This gasket provides an air tight seal between the carburetor and the plate. It is made out of compound material and it is sold individually. You will need a screwdriver and a wrench to complete this repair.

This genuine replacement screw is a high-quality OEM part designed for use with Paramount and Poulan gas-powered lawn and garden equipment. It is specifically engineered to secure the starter rope within the pulley, ensuring reliable starting performance. Made from durable metal, this specialty screw is sold individually. Installation...Read more Tip: A flat-head screwdriver is required for removal and installation. For proper placement and application, please refer to your equipment’s model diagram.

This is a genuine part sourced directly from the manufacturer. The Washer-thrust is commonly found in Poulan, Husqvarna and Jonsered chainsaws. The washer is utilized to provide a tight fit between connected parts. It is a high-quality replacement for a damaged or a missing hardware that was installed on a new unit. Refer to the diagrams ...Read morefor your model to ensure the exact location and the correct application of this part. Keep in mind this washer is made of durable metal and is sold as an individual item.

This is an authentic Poulan replacement chain designed for use with chainsaws. It is a key component of a chainsaw which mechanically cuts the material. Over time the chain will stretch, become dull or break. Keep an eye on the condition of the chain and replace as needed. Please note this chain is only for use with 16" bars. Includes one...Read more (1) metal cutting chain per order. The only tool needed for this repair is the scwrench that most likely came with your chainsaw. Otherwise, a flat head screwdriver and a socket wrench will do just fine. • Remove the guide bar side panel • Release the chain tension • Remove the old chain • Loosen the tension screw • Thread the new chain onto the saw • Align the guide bar • Replace the side plate • Tighten the chain to the correct tension • Finish tightening the side plate nuts

This is an authentic replacement part sourced from original manufacturer. It is commonly used on gas chainsaws. A centrifugal clutch is a part that uses centrifugal force to connect two concentric shafts, with the driving shaft nested inside the driven shaft. Today's centrifugal clutches will function even when they shouldn't, far beyond ...Read morethe point of when they need to be replaced. Keeping an eye on equipment performance will determine when the centrifugal clutch requires attention. This clutch is made out of metal and it is sold individually. Please note the clutch drum, spacer and washer are all sold separately. To replace this item you would need a screwdriver and pliers.

This replacement part is an authentic OEM screw designed for use with gas chainsaws and trimmers. This item is generally used to secure the housing of the equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. To secure or loosen this screw you would need a phillips head screwdriver.

This check valve, also known as a one-way valve, is a genuine OEM part that regulates the flow of fuel/oil in the equipment engine to prevent it from flowing backwards. It is made of plastic and designed for use in a variety of lawn and garden power equipment. If the valve is jammed, worn down, or contaminated with dirt and debris, it wil...Read morel be unable to open and close properly, thus restricting the flow of fuel and compromising the engine combustion process. You will likely notice fuel leaks around the carburetor, engine stalling, hard starting, and overall lower performance from your equipment. To remove the faulty valve, carefully disconnect any hoses or fasteners connected to it. Place the new valve in position and secure it appropriately.

This is an authentic component which is supplied directly from the original equipment manufacturer for use with Poulan and Husqvarna chainsaws. The flywheel has magnets on its side that create an electric charge as the magnets pass the ignition module. The electric charge is sent to the spark plug to fire the air-fuel mix in the cylinder....Read more The flywheel fits on the crankshaft by a key that aligns with a keyway on the crankshaft, this allows for proper firing timing. Keep in mind this high-quality flywheel assembly is made of durable metal and is sold individually. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component.