- Home
- PDW9280J10SS
- Instructions
PDW9280J10SS General Electric Dishwasher - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
water inlet valve leaking
1 person
found this instruction helpful.
-
Brad from wadsworth, OH
- Easy
- 15 - 30 mins
-
Pliers, Socket set, Wrench set
I had a shut off water supply shut off shut under my sink. That is where I shut the water off for the dishwasher. I knew it was for the dishwasher ,because it follow the line, and could see it was going to the washer. Then I went down stairs in the basement. Opened my breaker box, and found the breaker for the dish washer marked dish wash
... Read more
er, and put in the off position. When I was still up stairs I opened dish washer , and inside at the top was two screws holding the dishwasher to the counter top. Those two screws turned out to be the exact size of just about every screw I ended up having to unscrew on this machine. So at the time I was in the basement turning off breaker, I went to the garage to gather up tools. Take the two screws that are screwed to the counter top. Then I layed on the floor, and at the bottom of the dish washer there is a panel on the front of the machine with screws attaching it. Take those screws out. Pull off cover. Now get a flash light so you can see. They're adjustable feet that the dishwasher are being leveled by. Those feet need to most likely be adjusted down so you can the machine pulled out, and make it possible to work on. now you can you can pull it out, but watch that water supply line does not get hung up, or electrical wires. Once the machine is pulled out there is another cover on the front that I took off. Four screws hold it on. Now you can get to the part to fix it. The other thing you need to know is after taking off the valve and taking off the old 90 fitting. It will need cleaned up. When you put it on the new shut off valve use pipe dope or thread tape so it doesn't leak. Good luck.
Read less
Was this helpful?
Thank you for voting!
Old rollers broken
1 person
found this instruction helpful.
-
Thomas from TAMPA, FL
- Really Easy
- Less than 15 mins
No instructions. At first thought I needed instructions. A minute later I was attaching the new rollers. Simple and easy. Took less than 15 minutes. Would recommend these rollers.
Was this helpful?
Thank you for voting!
Food particles had started stopping up spray arm and get them out.
1 person
found this instruction helpful.
-
carla from valdosta, GA
- Very Easy
- Less than 15 mins
Pulled old spray arm off and snapped new one on. Less than 3 minutes and works great. Dishes are cleaner now.
Was this helpful?
Thank you for voting!
Started to have a leak
1 person
found this instruction helpful.
-
Ron from TYNGSBORO, MA
- Really Easy
- Less than 15 mins
Pull out the old, died gasket. Clean out track that holds gasket. insert new gasket.
Was this helpful?
Thank you for voting!
Dishwasher was noisy during drying cycle.
1 person
found this instruction helpful.
-
Carl from SUMMERFIELD, FL
- Easy
- 30 - 60 mins
-
Screw drivers
The noise came from the dishwasher door. Removed the Phillips screws from the door edge to gain access by separating the front of the door. Had to disconnect some of the electrical connectors to allow more access. Disconnected the blower motor connector. Removed the screws holding the motor assembly and removed the blower motor. Inst
... Read more
alled the new blower motor and reconnected the electrical connectors. Reassembled the door and cycled the dishwasher. Very quiet now!
Read less
Was this helpful?
Thank you for voting!
Plastic coupling broke on door cable counter balance
1 person
found this instruction helpful.
-
Todd from DALLAS, TX
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Removed dishwasher from under counter. Removed both cable pulleys and bushings. Threaded new cables and remounted pulleys and bushings. Finally stretched springs onto cables. Checked counter balance and reinstalled dishwasher.
Other Parts Used:
Was this helpful?
Thank you for voting!
wouldn't drain
3 of 7 people
found this instruction helpful.
-
JOHN D. from GOSHEN, IN
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Removed the dishwasher to get at the defective parts and removed,than replaced the two check valves and reassemble.
Was this helpful?
Thank you for voting!
Leaking valve
1 person
found this instruction helpful.
-
Gary from HAVERHILL, MA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Used teflon tape around new 3/8 elbow. Re-installed valve in originals postion. Connected supply hose and reconnected electrical to valve.
Was this helpful?
Thank you for voting!
Would only drain intermittenly
1 person
found this instruction helpful.
-
C. from Lexington, KY
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Thought it might be check flapper valve on drain pump, so I replaced fairly easily, per instructions. When doing, I noticed the attached relay wires were not secure. When it was on the drain cycle one of the relay wires vibrated badly and loosened the connection enough to only work occasionaly. Would like to put new relay on the pump bu
... Read more
t they do not sell separately from the pump. (one assembly). I resecured connection and will wait till relay gives out and buy new assembly, but for now it's working perfectly!
Read less
Was this helpful?
Thank you for voting!
valve leaked
1 person
found this instruction helpful.
-
Paul from KENT, WA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Wrench set
shut off water. removed lower panel disconnected power removed supply hose and outlet hose. disconnected electrical plug from valve. Un bolted valve from frame. removed elbow from valve inlet. installed elbow on new valve using Teflon tape. reinstalled valve to frame. connect hoses + electric plug to new valve. turn water on che
... Read more
ck for leaks. reconnect power. run dish washer check for leaks & popper operation. reinstall lower panel.
Read less
Was this helpful?
Thank you for voting!
Mainly leaking Rince Aid, but occasionally the soap door did not open to dispense soap
1 person
found this instruction helpful.
-
Edward from AVON, IN
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Watched the video, and followed the directions. Although my machine had some slight differences, the repair went pretty much per the video. Got all connections back where they belonged, cleaned up the insides a little while had the door parts separated, then buttoned it all back up, ran a cleaning solution thru empty washer, let it dry
... Read more
then started filling with dishes and ran the wash cycle the next day when full. All is well.
Read less
Was this helpful?
Thank you for voting!
New install missing drain tube and clamp.
2 of 4 people
found this instruction helpful.
-
David from Norwell, MA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
Purchased new $1400 dishwasher from sales floor for $699. Cosmetically perfect, but missing drain tube and clamp. Seemed like a good deal... and it was. Needed parts were $34. Install of this machine was a breeze, and it is suoer quiet...I need to get down on the floor and listen for water flow to know that it's working. Really.
Other Parts Used:
Was this helpful?
Thank you for voting!
No video for this new version of the part
1 person
found this instruction helpful.
-
Ellen from DOVER, DE
- Easy
- 15 - 30 mins
The entire flat side of the end cap, (with the cutout latch), goes on the outside of the guide bar. It took less than 15 seconds to insert. It took about 30 minutes of searching for videos and playing around with the part to figure this out. A simple diagram would have been helpful.
Was this helpful?
Thank you for voting!
Old soap dispensor latch would not hold
2 of 4 people
found this instruction helpful.
-
Kenneth from Dublin, OH
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caul
... Read more
k around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.
Read less
Was this helpful?
Thank you for voting!
Detergent dispenser did not work
1 person
found this instruction helpful.
-
ARTHUR from OAK PARK, IL
- Very Difficult
- More than 2 hours
-
Pliers, Screw drivers
Followed the instruction video on your website. It was accurate and valid. The repair should have taken 15 mins., instead one of the screws holding the dispenser was frozen. Tried DW-40, and liquid wrench. Neither worked because the screw was in plastic.Finally got out the Dremel and cutting wheels. Had to cut away enough of the unit unt
... Read more
il I could get at the screw (it was the center bottom one). Sliced through some more of the housing, then cut a notch in the screw head deep enough so I could apply enough pressure with a flat blade screwdriver to open it. After that things went as smoothly as could be expected.A bad design and cheap materials.
Read less
Was this helpful?
Thank you for voting!