EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

PDW8700J10CC General Electric Dishwasher - Instructions

All Instructions for the PDW8700J10CC
16 - 30 of 432

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water was not draining out of the bottom of the basin
28 of 31 people found this instruction helpful.
  • Eric from Leander, TX
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Wrench (Adjustable)
The dishwasher was disconnected and pulled out. I turned it over onto it's side so I could get down to the drain pump. It looked exactly like the original part and fit just as well. The hoses came right off and then once it was replaced, slipped right back on. It all worked like a charm. The only problem I had was after the repair. T he copper water line moved around too much and caused a leak at the connection at the dishwasher. Luckily I tested the line outside before I reinstalled it completely. I just went and bought an $11 flexible hose with new fittings on either end and replaced the copper lines. It went on easier and it sealed tight.

This was a pretty easy repair and I am glad I did it. We were on the verge of just buying a new one, but for a $35 part and a couple hours, it was well worth it.
Was this helpful?
Thank you for voting!
plastic hinge arm link broke causing door to flop open
28 of 35 people found this instruction helpful.
  • Margaret from Meridian, MS
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
First I had to unscrew screws under the counter then pulled built in dishwasher out from under the counter, attached hing arm link to right side bracket on door, and the other end I attatched to a spring at the back of the unit. Thats it! and pushed the dishwasher back into place. All back to normal....by the way Im a 67 yr old great gra ndmother...
Was this helpful?
Thank you for voting!
Lower rack on my dishwasher had rusted out, due to use, wear and tear, normal use
20 of 22 people found this instruction helpful.
  • Helga from Wayland, MA
  • Really Easy
  • Less than 15 mins
I took out the old rack and put in the new rack. Took about 20 seconds tops. But I had thought I needed to order the wheels (8 of them) and the wheel attachments (8 of those, too) separately because when you go to order the rack, it is suggested that you buy those, too. But the rack came with all the parts I needed so I ended up returnin g the stud rollers. Very happy with the product and the friendly service.
Was this helpful?
Thank you for voting!
Noise, Poor cleaning
23 of 33 people found this instruction helpful.
  • Vern from Orem, UT
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Turned power off, removed dishwasher, tipped on side, removed and installed pump asym, reinstalled
Was this helpful?
Thank you for voting!
cap was melted
17 of 18 people found this instruction helpful.
  • Greg from Doon, IA
  • Really Easy
  • Less than 15 mins
replaced it
Was this helpful?
Thank you for voting!
Broken drawer slides
21 of 31 people found this instruction helpful.
  • steve from ramsey, MN
  • Really Easy
  • Less than 15 mins
The repair was very easy, I just had to replace some bad bearing slides in the drawer pull. Remove the end cap, remove the top drawer, remove the old bearing slide from the drawer slide and snap the new one in. finally replacing the end caps.
Ordering the parts was easy and delivery was fast.
Was this helpful?
Thank you for voting!
Sump was leaking from previous repair person
20 of 28 people found this instruction helpful.
  • Jan from Boise, ID
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers, Wrench set
Removed Dishwasher, inverted it and replaced the sump housing. There are 2 screws mounting the top of the dishwasher to the counter, a water connection and the electrical connection. Remember to turn the water off and the electricity off. Slide the DW out on carpet. Carried it to the garage to affect the repair. Reinstalled the dishw asher. Most difficult part of this is that the water hose is really short. I used a 6ft extension so that the next time I have to pull this out it will be easier.
Was this helpful?
Thank you for voting!
Soap dispenser latch broke - never worked right
16 of 17 people found this instruction helpful.
  • Steve from Lincoln, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
This was a piece of cake. The original soap dispenser never worked right and always left unused soap. The new part was easy to install and works great. Only needed a 1/4" nut driver and philips screw driver to pull the outside panel and replace the module rinse and cap assy. Easy!
Was this helpful?
Thank you for voting!
Metal cover broke off of lower spray arm and gluing didn't work.
14 of 14 people found this instruction helpful.
  • Steven from Holland, PA
  • Really Easy
  • Less than 15 mins
Turned spray arm while lifting upward to remove the old part. Place new spray arm over the water outlet and turned with light downward pressure until properly seated.

It less time to do the repair than it took to open the box and unwrap the part!
Was this helpful?
Thank you for voting!
The bottom rack had broken wheels and rusted prongs
14 of 15 people found this instruction helpful.
  • MONICA from ENCINITAS, CA
  • Really Easy
  • Less than 15 mins
Exactly as described by a previous reviewer. I pulled out the old rack, put in the new rack and just moved over the cutlery rack.
Was this helpful?
Thank you for voting!
Leaking water when in use.
16 of 22 people found this instruction helpful.
  • J from Walnut, CA
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set
Part was an exact match. Make sure to use plumber's tape on all threads. Had to really tighten fittings to prevent leaks. Screws are a little difficult to get to. Test for leaks first, before final installation.
Was this helpful?
Thank you for voting!
Actuator was broken
15 of 20 people found this instruction helpful.
  • Sally from Saint George, UT
  • Easy
  • Less than 15 mins
  • Screw drivers
When I first tried to fix the handle I could not figure out where the spring went. I went back online and looked at the diagram of the dishwasher on this site and learned where it went. Once I knew where every piece went it only took me about 5 minutes to put it back in and another 5 minutes to screw the cover back on. I am a newer hom eowner and want to be able to do minor fixes. This was my first one and was very happy that I was able to do it on my own.
Was this helpful?
Thank you for voting!
Lower Rack would no longer roll out. Had to lift out lower rack.
12 of 14 people found this instruction helpful.
  • William from Ramsey, NJ
  • Really Easy
  • Less than 15 mins
Once we ordered both the "Stud Roller" and "Roller Lower Rack" the repair was simple.

The previous studs mostly disitegrated, so their removal was not an issue. The wheels pulled off easily.

I recomend getting new studs and rollers for all of the wheels on your rack. For me, that was 8 wheels and 8 studs.