PDT760SSFSS General Electric Range - Instructions

Originally I thought that the Start switch was the issue, and ordered one. After taking the machine apart and running some tests, the issue was clearly not this switch, but a different switch that cuts power when the belt tension is no longer being applied to the idler pulley spring. I fixed this by bypassing this switch, which in my op ... Read more inion, is error prone and serves no purpose. The switch can be accessed by removing the control panel, then top cover, then front cover, then drum. The bogus switch is screwed to the bottom left, near the motor. The idler pulley spring rests against it. Just disconnect the switch wires, then clip, strip and crimp then together to bypass the switch, and voila! Now if the belt breaks or comes off the pulley, the motor will continue to run, but you wont hear the wet clothes flopping around, so that will be the indication that you have a belt problem. Hope that helps!

1st replacement part was damaged from Shipping.
Parts Select sent a new one that i received in only a few days.
our stove is slid into a granite island so the disassembly was not as simple as most. It was necessary to remove the controls, the controls housing & screws along the top of the oven door.
Within an hour the sto ... Read more ve was back in place and working perfectly.
Great service from Parts Select

Follow YouTube "how to change dryer's belt" some video is very clear.

Ordered the part. Received the box damaged and did not realize the part was damaged until our son came all the way from Columbus Ohio to install it. We ordered another part which came in a timely manner. Even though I reported the problem and told them that we are not very computer literate they still would not accept that the part was da ... Read more maged until we sent a picture. Our son came back from Columbus to install the new part which took about an hour. He took pictures which I was then able to send. They then asked for a serial number. I had already sent all the numbers from the part but that is when they said they wanted the serial number from the stove. We are elderly and getting that required me getting on my hands and knees to get it near the floor. Luckily I was able to get up. After multiple emails I now have to send the part back. Good luck to anyone working with this company. I will be waiting for them to reimburse me for the defective part.

Unscrewed the stove top and replaced the element.

Took off cover plate and removed screws from housing to switch. Connected each wire from old switch to new one. No problems.

Performed repair using a video for reference.

Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and scr ... Read more ews. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.

less then ten minutes, used a electric screw driver and in a snap, finished, I always buy my parts on line at parts select my stove is old but in good condition except parts give out sometimes and I just order part and keep on cooking.

Remove the draw from the stove. Then unscrew two Phillips Head screws ( one on each side). Remove the old gliders. Slip in the new gliders. Screw the two phillis head screws back in. Make sure when you put the drawer back in the stove that you lift the front of the drawer up enough that the lower portion of the new glider is engaged on t ... Read more he side rail of the oven drawer space.

easy to fix took less than 10 minutes

Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.

My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),r ... Read more ed] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.

I removed the cooktop from the countertop and propped it up with 2 1x2's on each end. I removed the Torx screws that hold the glass in place. I set the glass aside. I then removed the screws holding the cover for the switches. I set the large central burner aside. I had to spray the screws holding the switch cover in place to loosen ... Read more them. I then removed the defective left front switch and replaced the it with the GE Parts Select replacement switch. I then put everything back together. This Utube video was helpful although not my model number https://www.youtube.com/watch?v=tmcUqpHNj3Q

I removed the top cover and the back cover to install new belt.
Once i put new belt i discovered that the pulley was also broken so now i have order the pulley so that i can complete the repair