PCB900DP1WW General Electric Range - Instructions

easily lifted the top of the stove after removing two small screws in front of the stove.removed screws holding burner in place , disconnected some wires and replaced burner. be sure to turn off the power before beginning this project

Pulled the oven out of it's location. Disconnected the power cord from the Electrical Outlet. Removed the Protective back plate (from the rear of the oven) which covers the wiring. Disconnected the two leads that connect the Baking Element. Went to the front of the Oven, opened the oven door, removed the two screws with a socket wrench (y ... Read more ou can use a screw driver as well), at this point you can replace the element with the new one and secure with the two screws. I then went back to the rear of the oven and reconnected the two wires back onto the new heating element and replaced the wiring protective back plate. Reconnected the power cord to the electrical outlet and turned on the oven to see if the element heats up. AND IT DID. Moved oven back into it's original location and I was done. This took 16 minutes to do and saved me a nice amount of money. I could have had a service person show up and do this work which would have cost me $189.00 (Parts & Labor) to have done and all I spent , by ordering the part from PARTSELECT.COM, was just under $50.00.

The first step was to determine whether the problem was with the fan itself or the switch. I did this by opening the back cover and using a Volt meter to verify that the fan was not getting power. (I could have skipped this step.)

Next, I unplugged the range, closed up the back cover and lifted the range hood by removing two he ... Read more x head screws that are just inside and on either side of the top of the opening in the range door. Propping the hood open, I removed the connector leading to the switch, then pushed the switch out the front. Inspection showed that the switch was damaged so I closed up the range and ordered the part from Part Select. Once the part arrived, it was a 15 minute job to unplug the range, lift the top, install the new switch, and close up the unit.

Caution. On starting to install the switch, I failed to unplug the range and my finger brushed one of the hot contacts leading to the switch. Thankfully, I was not injured. Do not repeat my mistake on this issue. Unplug the range even if you're only installing this simple switch.

Replacement was extremely easy. The new part fit perfectly and installed very easily without tools. Also, I received the part within a few days

I (1) pulled the oven away from the wall to get the back of it exposed. Then I (2) pulled the plug out to make sure there was no electrical current. Then I (3) opened the oven door and tugged on the broken heating element to see how tightly it was connected in the back of the oven. Next I (4) went to the back again and slid the silver-c ... Read more olored metal cover that protected the exposed electrical wiring for the oven. I (5) observed that there were a number of different colored wires held in place by screws as well as some wires that disappeared into the insulation, so I (6) went back to the front of the oven and pushed the broken heating element backward to determine if its wiring would become visible from the back of the stove. I (7) observed from teh back that it did. From that point, I (8) pulled the heating element's wiring connections through the insulation until it was visible. The I (9) unscrewed the two nuts connecting the heating element to the oven's wiring. Then I (10) went back to the front and pulled the broken heating element out and (11)inserted the new heating element. Then I (12) returned to the back and connected the loose wires to the heating element and (13) pushed the heating element forward into the oven. I (14) went around to the front to ensure the heating element was positioned the same way in the oven as the old one was, then in the back (15) replaced the metal shield over the wiring and isulation, (16) plugged the oven back in and (17) turned the oven baking setting on to a high temperature to test the new element (i.e., that it was connected correctly and actually worked). I (18) observed that the oven began heating up quickly to the proper temperature, and I was greateful the new bake element worked as good the original part. I then (19) turned the oven off and pushed it all the way back to its place against the wall.

The repair job was not effortless (about 15-20 minutes) but was simple enough NOT to require an electrician. The most difficult part was physically sliding the stove out and back into its tight place between our counters.

I order the part online on the 23rd of February 09 in the afternoon it was delivered on the 24th to the address in Florida and then fedex to me in Cayman. So I got it on the 2nd of March went home that evening after work got my pliers unpluged the stove removed the two screws that holds the element in place. I also removed the metal from ... Read more the back of the unit first to make sure I was doing it right. I then pulled the element at the back and disconnected the two wires replacing it with the new one. I then replaced the back and screws and pluged it in turned on the oven waited and when I saw it turn red I felt so good. I said thank you Lord and then baked a cake. The whole installation took about 20 mins.
Thanks again.
P.S. please look into offering shipping orders overseas.

I am a 69 year old woman. I watched the Repair Clinic YouTube Video before I started. I then pulled stove away from wall and unplugged it. Took off oven door and removed the top oven rack. Loosened and removed the screw holding the temperature sensor located inside at the top center back wall of the oven. Pulled the sensor through th ... Read more e opening until the plastic plug came through. Unplugged and removed it and plugged in the new sensor. Fished it back through the opening. Replaced the bracket to the back wall of the oven and tightened the screw. Replaced the oven rack and stove door. Plugged it back in and moved it back into place. I turned on the oven and let is heat for over 30 minutes and the internal temperature was correct with the setting.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

With circuit breaker off, I opened the oven door and removed the two mounting hex-head screws that held the cooking element at the rear of the oven. I pulled the oven away from the wall and unplugged the unit's 220 volt power cord from the wall. I removed the rear cover panel by removing five hex-head screws that held the panel in place ... Read more . I sought out the wires that connected to the oven element and pulled the tabs from the failed element. I moved to the front of the stove to remove the old element. As the contact ends of the element are curved up, I needed to lift the front of the old element up to an approximate angle of 45 degrees before I was able to remove it from the oven. I then placed the new element into the mounting holes, again with the front of the element raised at an angle. Its insertion was easily performed. I replaced the main element mounting screws at the rear of the oven. I went to the rear of stove again and reconnected the power tabs to the element contacts. I repositioned the rear cover panel and replaced the five hex-head screws to secure it into place. The main power was reconnected to the power outlet and carefully slid the stove back into position. Circuit power was reset and the oven tested successfully.

Pull the old one put in the new one ... took about 20 minutes

My oven bake element melted one day. I had my husband replace it and for a short while it worked. Then it quit but then our broil element would not shut off. My husband said that it might be the heat sensor. We checked here in town and that element cost over $80. Since we have order from Parts Select before we decide to do so again. When ... Read more we received the heat sensor my husband replaced it taking out the original heat sensor. This did not work as the broil element still would not turn off. I call the repair man and I found out that the initial melt down of the bake element also effected the main circut board that had to e replaced.

Scary when stove burner comes on by itself, was turning breaker off for safety! GE website not helpful at all. PartSelect website enabled diagnosis of problem and then provided easy source for replacement switch. PartSelect has schematics: all I had to do is unscrew the back of control panel, unscrew offending infinite switch, hook up ... Read more replacement switch same way, put panel back and done. GE service call starts at $80 and then who knows what kinda $$$? Did repair myself: cost just $38. Yay!

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appl ... Read more iance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

First turned off power at breaker box. Pulled stove out to remove the half dozen hex screws on the back panel.(some nuts were stripped)Removed old oven sensor inside oven held by one hex screw and replaced it with the new part. Oven works great now! Repair job was done by husband Mike.

1.) I removed the old oven door gasket by taking out the ends of the gasket out of the bottom of the oven door first.
2.) Pry up on each one of the retainer clips, they easily pop out of their slots.
3.) Work your way around the oven door gasket.
4.) If any remain stuck you can just wiggle the clip around and it should po ... Read more p out of each hole. If need be you could use pliers, but I did not need to.
5.) Take your new gasket, it should already have new clips, so you can throw away the old ones.
6.) Work your way around the oven door making sure the clips are nicely seated.
7.) Finish off by inserting the ends back into the 2 holes on each side of the bottom of the oven door, I just used a small spoon to make sure the tops were nicely placed in.
8.) If your gasket needs to compress, you can close the oven door and lock it that should hold it in place and compress it.
9.) All done!