MWS939AS0 Frigidaire Washer - Instructions

After moving machine to an area that allowed easy access to the unit, disconnected the water supply hoses from the inlet valve.
Removed the two screws that keep the back in place, removed the clips that keep the top in place, moved the top over far enough to get the valve out. Removed the screw that keeps the inlet valve in place, di ... Read more sconnected the power supply to the valve, Pulled valve out in order to remove the water outlet hose. Repalced with new vale, and reversed order to install. Works just fine now.

Happened to slam the lid by mistake and the washer started spinning. Recognized the lid lock was working haphazzardly. Also, there was a burning type odor coming from the switch. So I lifted the lid top and disconnected the switch from the lid by unscrewing 2 screws and 4 wires. When I received the new switch, I reinstalled it with 2 ... Read more screws and reconnected the 4 wires.

ordered part from parts select, it was the wrong part,( all my fault) they refunded part upon return and sent the new part, the return was easy and prompt, new part arrived, 15 minutes wife was washing and happy again, and we all know, happy wife happy life, thanks part select!!!

First I removed the two screws that hold the pump in place. I then pulled the pump out and replaced it with the new pump.

I pulled the old motor out of the bottom of the washer. After undoing the screws and taking off the belt. I threw the new one in and tightened everything up and put the belt back on and it worked great... Super easy to change a motor out and a lot cheaper than buying a new waher...

The best part was that it only took one d ... Read more ay to ship to my house and I picked the cheapest shipping amount... I recommend this site..

i removed the front panel, then removed the old pump by taking off the clamps and disconnected the wiring. The new pump had to be reversed before connecting, but it was so easy.

followed the instructions on a blog

Lifted top
removed adgetator
removed tub top
removed inside tub
removed inside tub holder bracket
repaced seal
replaced,replaced.....

I'm a 70 year old widow.. ordered the part which came in 2 days..(.very reasonably priced) My son came over and in no time had the old out and new in...works like a new machine... Thank you Part Select. A few months ago ordered a stove ignitor..it too came really fast... stove is good for another 15 years..LOL

After the new replacement part arrived, I took off the complete back panel (after unplugging the electrical and shutting off the hot & cold water supply). I disconnected both hot & cold water hoses, unscrewed the 2 screws holding the water valve, unplugged the 2 electrical wires for the water valve sending unit, unclamped the outlet water ... Read more hose. Then I reversed order with new water valve. Put everthing back together in about 20 minutes overall. I did also replace the hot & cold water supply hoses with a better quality hose. Works like new! Thank you very much.

removed the two 'lock down flanges' from the back of the machine, lifted the top from the front and slid it forward to access the valve. Removed the two electrical connections then the compression ring from the hose on the output side. Removed two screws holding the valve in place, then reversed the process.

I wish this valve w ... Read more as made of metal rather than plastic. I had to replace it because the threads were stripped. Here's the heads up. Make sure the fittings on your supply hoses are 'clean' or you'll mess up the plastic threads and not get a good seal.

Removed back cover; pulled knob off front (removed small screw). Removed hose connected to pressure switch. Removed old switch. Electrical connections are numbered 1-2-3, and the part positions are also numbered 1-2-3. Pulled off old, installed new. Reconnected hose. Rehooked screw on front, replace knob and back cover.

I removed the top of the washer by removing two screws on the back. I located and bypassed the lid switch to make sure that wasn't the problem. The problem still existed so I removed the two screws that hold the front panel of the washer. Using a flashlight, I located the drive belt and immediately saw that it was out of position and h ... Read more ad pieces missing. I cut and removed the old belt, placed the new belt on the tub pulley and slowly maneuvered it onto the motor drive wheel. I then squeezed the tensioner pulley so that the belt was seated. I turned the timer dial which started the washer and it immediately began pumping the water out of the tub. Problem solved!

S/O Water , Removed front panel, removed screws from side panel water valve accessible. Removed screws that hold water valve, installed new valve reassembled washing machine.

removed old agitator by loosing a bolt at top, after removing the detergent dispenser. agitator came off easily, new one on, bolt on with rachet wrench, dispencer on. works like new. thanks for the great service. the part came in faster than i thought it would, and i would have had to travel for miles to get a part around here. VAL