This part is a genuine manufacturer door interlock switch kit, also known as primary micro switch or microwave switch kit, for a microwave. The function of this part is to sense when the door of the microwave is open or closed. If the part is defective, the microwave will not start or will start when door is open. This kit contains two 15...Read more Amp, 125/250 Volt switches with 3/16 inch terminals. Be sure to disconnect power to microwave before replacing part. Use extreme caution when replacing microwave parts, as high-voltage capacitors can retain an electrical charge when unplugged. NOTE: This kit includes 2 single pole, double throw (SPDT) micro switches. As per the manufacture for the secondary interlock switch order part # 56001100.
This is a cooking tray, but may also be known as a turntable tray, and it is used in conjunction with your microwave or oven/microwave combo. The outer diameter of this part is roughly 12.75 inches. The tray is made entirely of glass and is colorless. The purpose of this part is to act as a stable and even cooking surface for your food to...Read more sit on during a cooking cycle. To ensure a more even cooking temperature the tray will also spin when your appliance is activated. The most common reason for needing to replace this part is if your current one has been damaged.
The rectifier (also known as a diode) provides the microwave with energy to cook food. If your appliance is not producing heat or not turning on it could be due to the breakdown of the rectifier. This part works with microwaves, microwave oven combos, and wall ovens. This is one of the most common parts to fail over time in a microwave. T...Read morehis part is just under 3-1/2 inches in length. It is a genuine OEM part that is shipped right from the manufacturer. Make sure to use the proper precautions before attempting this repair. Ensure the appliance is unplugged.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Microwave worked intermittently depending on how door was closed
67 of 85 peoplefound this instruction helpful.
Robert from Bainbridge Island, WA
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers
Remove top grille (2 screws), undo control panel (1 screw). Tilt down control panel, switches are on the left. There are actually three switches that are involved with the door, two horizontally mounted, one vertically mounted. This would be an EASY REPAIR, but it took me a while to figure out which of the three switches was bad, and a
... Read morelso took a while to figure out that there is a plastic rod that inserts through the hole in the switch body. Once i figured this out went like a breeze. Lower horizontal switch was the bad one, but since the kit came with two switches i went ahead and replaced the upper horizontal one as well. IT appears that the horizontal switches are probably more likely to fail than the vertical switch based on the position of the switch and force angles. Works great now!
Read less
Was this helpful?
Thank you for voting!
Close the door on the microwave, punch in the # nothing happened
15 of 23 peoplefound this instruction helpful.
Robert S. from Stafford, TX
Really Easy
15 - 30 mins
Screw drivers
I removed the unit from the wall. Took the cover off. Set the unit on its side. It revealed the working parts. Removed the old micro switches. Put in the new oness. Presto, it worked. Very easy for me. The parts was delivered almost before my notice they were shipped.
Was this helpful?
Thank you for voting!
Needed to push door up to run appliance.
15 of 28 peoplefound this instruction helpful.
J Patrick from Baltimore, MD
Easy
Less than 15 mins
Pliers, Screw drivers
1. Removed cabinet screws (10-15?). 2. Removed cabinet. 3. Removed top interlock switch which actually was not defective. The press clip connection appeared as if it had been arcing for quite some time and the corrosion created resistance sufficient to prevent the current from getting through the switch. 4. Replaced switch anyway but brok
... Read moree plastic retaining clip despite every effort not to do so. Reset broken clip with super glue. 5. Reassembled cabinet and appliance is in good working condition.