Door Interlock Switch Kit 4392027

Hello Mike, thank you for your question. The module your referring to is probably the electronic control module part number WPW10169272. The issue might be that, but it could also be the door switches,diode, fuse or magentron. The door switches are very easy to test with a multi meter. I have included a link that will take you to lots of great information on the parts that could cause this same issue. If you think the module is the issue, that part is WPW10169272. You can enter that part number into our site to find the price and availability. I hope this helps! https://www.partselect.com/Repair/Microwave/No-Heat/

Hello Tim, Thanks for the question. We show that the switches should be tested with a multimeter, and replaced if they show no continuity. Please keep in mind that these parts should only be installed by a technician, as the microwave can still carry a charge even after being unplugged. I hope this helps.

Hello Fred, thank you for inquiring. You will want to replace the Door Interlock Switch Kit part PS373050. Be sure to disconnect power to the microwave before replacing this part. Use extreme caution when replacing microwave parts, as high-voltage capacitors can retain an electrical charge when unplugged. We hope this helps.

Hi Bill, Thank you for your question. Before you begin any repair please unplug the appliance from the electrical outlet. Use a Phillips head screw driver to unthread the screws securing the grill. With the screws removed, open the microwave oven door then the slide the grill to the left and lift it up to remove. Next remove the control panel mounting screw then lift the control panel up to detach. Then remove the screw holding the inner access panel and then release the panel from the retaining clips. Now remove the screws holding the switch assembly. Depress the release tab and the actuator to detach the switch you are replacing. Disconnect the wire connector to fully release the old switch. Install the new door switch by first connecting the wire connector. Now position the new switch in the assembly snap it into place. Realign the switch assembly on the frame and secure it with the screws. Reinstall the inner access panel securing it with the screw. Now insert the control panel tabs to the slots in the frame and push the panel down. Secure it with the mounting screw. Insert the tabs of the grill into the frame and slide it to the right. Shut the oven door and then secure the grill with the screws. Plug the power cord back in and the microwave should now work. I hope this helps. Thank you and have a great day!

Hello Sheldon, thank you for your question. The most likely issue is a bad door switch or switches. We would recommend testing them to determine which one(s) are faulty. Here is a link that will give instructions on how to test those switches. https://www.partselect.com/Microwave+test-door-switch+repair.htm. I hope this helps!

Hello Jerry, Thank you for contacting us. You would need to check the door switches with a multi-meter and replace the one that does not have continuity. I hope this helps!

Hello Bob, thank you for writing. It sounds as though the Door Interlock Switches may be faulty. This part number PS373050 is the correct replacement for your model. You may also want to consider the Door Latch part number PS11745097 for your model to fix this. I hope this helps and good luck with your repair!

Hi Jeff, thank you for your question. You will want to test your door switches to see if they are working correctly. You can do that with a multi meter. They should be ready 0 ohms. I hope that helps. Good luck with your repair.

Hi David, Thank you for your question. Here is some information you may reference on how to access the switches in your microwave. Before you begin any repair please unplug the appliance from the electrical outlet. Use a Phillips head screw driver to unthread the screws securing the grill. With the screws removed, open the microwave oven door then the slide the grill to the left and lift it up to remove. Next remove the control panel mounting screw then lift the control panel up to detach. Then remove the screw holding the inner access panel and then release the panel from the retaining clips. Now remove the screws holding the switch assembly. Depress the release tab and the actuator to detach the switch you are replacing. Disconnect the wire connector to fully release the old switch. Install the new door switch by first connecting the wire connector. Now position the new switch in the assembly snap it into place. Realign the switch assembly on the frame and secure it with the screws. Reinstall the inner access panel securing it with the screw. Now insert the control panel tabs to the slots in the frame and push the panel down. Secure it with the mounting screw. Insert the tabs of the grill into the frame and slide it to the right. Shut the oven door and then secure the grill with the screws. Plug the power cord back in and the microwave should now work. I hope this helps. Thank you and have a great day!

Hello Zehner, thank you for your question. The first parts we would recommend testing or replacing are the door switches. If those parts are fine, and are tested and are working properly, the issue could be the main control panel. I hope this helps!