MW55 - Instructions

Removed control panel, discharged HV capacitor. Removed old diode, tested to confirm failure. Replaced part. Other than the removal of the panel swapping the part was almost as easy as replacing a light bulb.

I removed the unit from the wall. Took the cover off. Set the unit on its side. It revealed the working parts. Removed the old micro switches. Put in the new oness. Presto, it worked. Very easy for me.
The parts was delivered almost before my notice they were shipped.

Tipped washer over on to the front side. Removed back panel. Removed the flex coupling to the water pump. Removed the old belt. Installed the new belt and reversed the process to put components back together.

It was very easy, just one screw to get the belt on, then it was just putting in place and putting it back together took the longest.

Problem would come and go. Found service schematic inside unit. Perform all the suggested tests. One possible solution was the primary interlock switch shown on the schematic and a check found the switch stuck. It would free up some times but would stick again in the open position. Ordered switch which was a simple plug in unit.

1. Removed cabinet screws (10-15?). 2. Removed cabinet. 3. Removed top interlock switch which actually was not defective. The press clip connection appeared as if it had been arcing for quite some time and the corrosion created resistance sufficient to prevent the current from getting through the switch. 4. Replaced switch anyway but brok ... Read more e plastic retaining clip despite every effort not to do so. Reset broken clip with super glue. 5. Reassembled cabinet and appliance is in good working condition.

Removed the front panel with a stiff putty knife, removed the worn belt. Placed the new belt on the front pully and than the rear pully, turning clockwise. After checking the spin cycle I put the front panel back on and I was done.

Replacing the inlet valve could not have been any easier. First, I removed the back plate of the washer using a socket wrench on the 2 screws. After removing the wiring attached to the valve, I then detached the valve from the plate with the same socket wrench.

I then loosened the clasp on the rubber hose and disconnected it ... Read more from the valve.

I replaced the new valve using exactly the same procedure, only in reverse. First attached the hose, the attached the valve to the back plate. Then replaced the back plate on the washing machine and reattached the hoses.

Replaced diode works great. your website said 92% diode was problem and it worked. Order fuse in case old was blown did not have to use it.

After removing the rear cover I removed all the hose connections as this gives a better access to the mounting screws. Next disconnect the drive coupling. Remove the 2 inner mount screws frist then remove the 3rd screw.
Reversing this procedure makes mounting the new pump easy. Also I went to GE's web site and downloaded the parts ... Read more sheet that also gave me the number for the proper pump.
E. Renico

This was not exactly the right part for my machine, well, it was the right part, it was just a different design ro something. It didn't quite sit in the same place as the original, and so, the little hose is crimped a little, which makes the washer really loud. It's ok because it works now without babysitting. It was not difficult to inst ... Read more all, just took off the top panel with the star drive bit thingy, and took the old part off, installed the new part (forced it into place) and got it running.

Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise

I went to your web suite to get part numbers. Found your videos. It told me what my problem was and how to fix it. Pull clip off. install new knob reinstall clip done. Very easy and fast. I couldn't even get a repairman out that fast.

I noticed the belt was off, first, then pulled it back on. Washer worked, but very noisily, as belt continued slippage. I bought new belt after reading how to repair, then when it arrived, I read how someone installed it without having to remove bolt, etc. I tried and succeeded. It agitates just fine, but stalls when spinning. It's ... Read more like the belt is too tight, now. i am gonna try rotating the rotating parts to see if that will help loosen it.

turned washer on side to get at the bolts holding motor. loosen bolts. remove flexable basket for water pump or one end of it. slide motor to loosen belt. remove and replace belt. use large screwdriver on motor to hold tension on belt while tightening nuts. hardest part was getting clamps back on the rubber basket.