MRTW Refrigerator - Instructions

I pulled the old gasket off and thoroughly cleaned the entire refrigerator door, including the area where the gasket would pop into. Starting at the two upper corners, I pushed the corners into the ridge in the door and used my thumbs to press the gasket in along the top of the door. I then went about halfway down the door using my thum ... Read more bs to push in the gasket. Then I pushed the lower corners in, taking my thumbs up either side of the door to finish installing that section then I pushed the bottom in, checking the lower corners to make sure they were secure. Then I closed the door and made sure the seal was secure on both sides of the door.

Remove the broken piece by tilting upward and then sliding straight out.
Simply replace with the new door shelf by aligning the small hooks with the slots on the door. Tilt the shelf up, insert the hooks into the slots and then tilt the shelf back down to its normal postion. It is now locked in place and you are done!

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

first i removed the four screws that hold the shelve in place disconnected the wire replace both diffuser-air,reconnected the wire and replaced the screws

No long shelf came with our new refrigerator, Frigdaire did not have one so I went on-line from you and it fit perfectly, now everything does not have to be in one big heap.

Removed screws. Rotate door handle, and slide it off anchor screw. Slide new door handle on anchor screw, and rotate door handle into position. Replace screws.

took out the broken, put in the new, lapsed time about 15 seconds. I keep looking in the fridge to enjoy how beautiful the new one looks.

Easily removed the original door gasket starting at an upper corner by pulling the old gasket off completely. I then cleaned the area where the new gasket was to be pressed into the channel on the door of the fridge. I also cleaned the area on the fridge where the new gasket would seat upon completion of the installation.

Wit ... Read more h that completed, I began in the upper right corner of the door, easily pressing the new gasket into the channel on the fridge door. I then pressed the upper left hand corner of the gasket into place, into the channel on the door. I then pressed the entire upper horizontal part of the gasket into the channel along the top of the fridge door.

I then pressed the left and right vertical portions of the gasket into the channels on the fridge door. I then pressed the lower left corner of the gasket into place, followed by the lower right hand corner into place of the bottom channel of the door.

Lastly, I pressed the lower horizontal portion of the gasket completely into the channel of the bottom of the fridge door.

Finally, I rechecked all portions of the gasket to be sure they were securely fitted into the channel of the door.

Mission accomplished in less than 15 minutes. It's a piece of cake to make this repair!

All I did was to take out the cracked pan and slide in the new one.Excellent service.I ordered the pan late evening one day the part arrrived not the next day but the day after.I expected that it would have taken a week or better.I recommend Part Select.com because of this.

just snap the new piece in place.

It was fairly easy. Only had to remove the back cardboard. Remove 3 screws and the power plug.
Replacing the screws took a little time the motor mount didn't seem to be tapped exactly for the screws supplied and it was in a tight area. Its working great now.

Pull refrigerator away from wall, being careful not to kink or break water line to ice maker, unplug refrigerator. Using 1/4" nutdriver, remove cardboard lower rear panel, bottom lifts out. Fan and motor are now directly in front of you, grasp the moter to stablize it, and using your other hand, pull fan hub from motor shaft. Be sure mot ... Read more or shaft is clean before reinstalling new fan blade, press new bladr onto motor shaft, until center of blade is centered on outlet side of fan housing. spin blade by hand to insure clearance. Plug refrigerator in and observe operation of fan, refrigerator needs to be calling for cooling for this fan to operate. Reinstall cardboard panel and move refrigerator back into position.

Opened refrigerator door removed old door seal by pulling door seal loose from door with fingers installed new seal by pressing new seal back in by hand took roughly 10 minutes to do only issue I had was with delivery my package was sent to the wrong house and was received 3 days late

My 4 year old grandson used the frig door as a swing.The bottom hinge cracked, then the door wouldn't seal. I propped the door up with some books, removed the broken hinge (2 bolts) and replaced with the new part. Simple fix on the door, only time will fix the 4 year old!

Rack door slid into place easily. Repair required no tools and took maybe 20 seconds to install!
Very easy job!