MRSF - Instructions

Watched a video on how to disassemble the old bucket and reassemble the new one. Piece of cake. Thank you for the part and how to video.

Henry

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

I did not know what kind of tool was needed to remove the screws so I asked at the hardware store. When i said the screw was star shaped, he sold me torque wrench with multiple heads. First I removed the screw holding the broken handle in place. I cleaned surfaces. Next I attempted to put the handle in place on the horizontal bar and the ... Read more n put the screw into the opening. That did not work. I jiggled the handle for a while but could not get the pegs into the holes. Finally, I just held the handle in place and began to turn the screw and the handle slid into place as the screw got tighter.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

Followed the video on parts page. I was worried I would brake the cover but learned from the video the right way to remove the front plate. I found the video very informing. Thank you for saving me a service call and the part cost was minimal compared to a new refrigerator .

took the auger off and baffle replaced the baffle put every thing back together installed back to the freezer tried it out it dont work have to tear into the the motor which works the auger to see if anything else is broke.

Remove back side cardboard access cover. About 6 dcrews need to be removed. Remove 9/16” bolt and lower compressor tray frame down to slide out wheel axel. Place wheel in slot and replace axel. Lift compressor tray and replace 9/16” bolt. Replace cardboard cover. Remove 2x4.

First I unscrewed the end of the oven door and realized I could replaced the parts easily that hold the handle on the door. Then I held the sharp, broken plastic ends with a towel and used my drill with a thingy that fits on a small hex nut and unscrewed the broken handle parts and removed them. All I had to do after that is screw on t ... Read more he new handle holders with the handle bar fit snuggly between them, presto, new handle bar installed. Great service from partselect. com. Would use them again.!

I read the previous repair stories and figured it couldn't be that tough. Mine actually had a slight deviation and I'm sure based on model...
To remove the oven door handle, I had to remove 3 screws (phillips) on the top of the hinged door. This allowed the face plate to easily pull away from the inside of the door. The existing hand ... Read more les were held in place by a single hex head screw each.
Voila, in 2 minutes the entire handle was off.
This is where things had a slight deviation.
The door end caps I bought had 2 alignment prongs that extended beyond the actual surface. My door did not have holes for them to go into. No big deal, I took some wire snippers and clipped the little plastic prongs off so it was flush like my old ones. That took about 3 minutes because I had to go back into the garage to get the tool :-)
My metal door handle bar did not want to go all the way in very easily into the end caps. I went back into the garage and got some WD40 and sprayed into all pieces and wiggled things back and forth for a few minutes, placing it against the oven a couple of times to ensure I had the bar was seated enough where the holes lined up with the oven.
I would recommend putting the end caps on the bar PRIOR to attaching one side to the oven. I originally did not do this and when it was difficult to get the bar on, I had to take it off so I could perform the procedure I just mentioned.
Honestly, the entire "job" took 10 minutes.

This is a very basic model refrigerator and the only model we could purchase when our machine failed suddenly. The new unit works just fine, but we really missed the snack storage of the higher level units. I ordered the parts for the next higher model Whirlpool side by side refrigerator and installed them without incident. They new sn ... Read more ack drawer is a little difficult to snap into place, but it fits perfectly and we certainly appreciated the extra snack drawer on our basic model.

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved m ... Read more e $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

Unplug refrigerator.
Pry switch out with putty knife
Remove two wires from switch
Attach wires to new switch
Push new switch into slot

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

I ordered two new ones from partselect.com. I figured if I was replacing the one for the refrigerator door I might as well do the freezer door too.
Very easy to take the old ones off, take the putty knife clean tracks out. Putting the new ones on, was a little harder to do. You have to start in the corner and push the gasket into t ... Read more he slot. You need strong hands to do this. Once I heard them click in, they guided themselves the rest of the way. Once they are on, check to make sure they touch the frame of the door. My freezer was perfect, but the refrigerator had an area of 25 inches that did not touch the frame. I called partselect.com and they sent out another new gasket for the refrigerator door. (I had to pay for this one but was told once I mailed in the defective one, they would credit me the cost of the returned one) I took off the bad gasket and installed the 2nd new gasket and that one was perfect.

Ordered gasket through this site pulled old gasket off, because my conquest had no screws on lining, Put new gasket on top and bottom first and kind of forced the edges into groove using heat gun cause gave me a little problem. But overall, it worked to perfection! Now to buy other gasket for refrigerator door!