EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

MRMR General Electric Range - Instructions

All Instructions for the MRMR
46 - 60 of 145

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Handle broke
2 of 2 people found this instruction helpful.
  • Dean from Harrisonburg, VA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Took off the inside ( this allowed me to clean the glass) panel. Removed the two end parts with a screw driver. Replace the parts and we were good to go.
Was this helpful?
Thank you for voting!
Both end caps were broken removed
2 of 2 people found this instruction helpful.
  • Johnson from LUFKIN, TX
  • Very Easy
  • 15 - 30 mins
Removed torx head screws. Removed broken pieces of the end caps. Replaced the handle installed the end cap screws.
Was this helpful?
Thank you for voting!
rusted trim strip
3 of 5 people found this instruction helpful.
  • Larry from Sarasota, FL
  • Really Easy
  • 15 - 30 mins
  • Socket set
remove screws, re-install screws
Was this helpful?
Thank you for voting!
broke
2 of 2 people found this instruction helpful.
  • Barbara from Winston Salem, NC
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
just replace the end cap with a new one all that was involue was to screw the new one in took about ten minutes and job done better than buying a new stove when the stove is still just like new. thank you for your on line help.
Was this helpful?
Thank you for voting!
Bottom trim piece on 24 year old stove had rusted. Replace trim piece was still available.
2 of 2 people found this instruction helpful.
  • Donald from FAYETTEVILLE, NY
  • Very Easy
  • Less than 15 mins
  • Socket set
Very simple. Lift oven door off brackets and set on floor. Remove sheet metal screws holding on existing trim piece, Clean area beneath trim.
Put new trim piece on, don't tighten any of the screws until all have been started as some adjustment is needed to align the holes for the screws.
Was this helpful?
Thank you for voting!
Replace door gasket on very old wall oven
2 of 2 people found this instruction helpful.
  • r from SUNNYVALE, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Repair went a lot faster and easier than I anticipated. Instructions are similar to those posted by others.
1. Verify that new gasket looks mostly like old gasket as best you can since not all of old gasket is visible.
2. Shut off circuit to oven (optional, but good practice)
3. Remove racks, trays, etc from oven to red uce weight at Step 7
4. Remove oven door by partially opening door to broiler position (about 20 degrees). Door should catch and stay open on its own. Slide up and lift off door. The “hinges” are spring loaded so carefully return them to closed position so they won’t snap shut on fingers.
5. Remove Phillips screws, one on each side wall of oven liner.
6. Remove two hex screws and metal gasket-holder on top center of oven liner.
7. Pull and slide oven liner out of oven mainframe about 1/4 “ to 3/8”. This may be the most difficult part of the job.
8. If possible to remove just a couple of inches of one bottom of old gasket (right side is easiest), verify that the cross-section profile of both old and new gaskets are essentially the same. If not, you have the wrong gasket.
9. Pull and remove old gasket. If gasket is dry and cracking, it may be necessary to scrape it out with putty knife, flat-blade screwdriver, etc. if it has fused to metal over the years. Note how it was installed on the metal edge of the oven liner.
10. Locate the mid-point on the new gasket length and begin inserting it at the top-center of the oven liner where you removed the two hex screws. Continue installing along both left and right sides of the liner. Each end of the gasket should extend to just above the respective hinge. No trimming should be necessary. Ensure a snug fit all along each side and top.
11. Push liner back into oven mainframe. Replace Phillips screws, gasket-holder, and hex screws.
11. Pull out each hinge to broiler position.
12. Replace door by sliding down onto hinges. Close door and check for tight fit against gaskets. Gaskets will flatten somewhat over time
13. Restore power, racks, trays, etc.
Was this helpful?
Thank you for voting!
lights blown out
6 of 14 people found this instruction helpful.
  • Gerald from WINTERVILLE, GA
  • Very Easy
  • Less than 15 mins
replaced lights in refrigirator and freezer
Was this helpful?
Thank you for voting!
Part rusted over time...22 years.
2 of 2 people found this instruction helpful.
  • Jeannene from HUNTINGTON, TX
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Unscrewed eight screws. Removed rusted part. Cleaned area with Windex. Replaced new part.
Was this helpful?
Thank you for voting!
bottom trim had rusted out from water build-up
3 of 6 people found this instruction helpful.
  • john from buford, GA
  • Really Easy
  • Less than 15 mins
  • Socket set
disassembled bottom trim on oven door.cleaned area of excess rust and installed trim piece.
Was this helpful?
Thank you for voting!
Stove Top Element Heat Varies
2 of 3 people found this instruction helpful.
  • William from Perryton, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
Removed stove top from counter, removed glass top by removing 10 phillps screws, removed control bracked, unplugged connectors(wires) on old control and plugged into the correct position on the new control, replace control on the bracket then reinstalled the stove top and placed the stove top back into counter.
Was this helpful?
Thank you for voting!
Heat element died
2 of 3 people found this instruction helpful.
  • Andrea Hines from ELGIN, AZ
  • Very Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Very easy to replace. So easy even a man can do it.
Was this helpful?
Thank you for voting!
Intermittent heat then no heat on oven element
2 of 3 people found this instruction helpful.
  • Bruce from AKRON, PA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.

One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.
Was this helpful?
Thank you for voting!
Replaced stove top burner element
1 person found this instruction helpful.
  • Steve from Forest, VA
  • Easy
  • 1- 2 hours
  • Screw drivers, Socket set
Disconnect stove electrical connection. Removed 2 bolts common to the upper stove top cover. Disconnected 4 wires from burner element along with 2 retaining clips.
Removed burner element and replaced with new element. Reinstalled 4 wires and 2 retaining clips. Lowered stove top cover and reinstalled 2 bolts. Connect stove electrical to wall outlet. Turn on burner element and verify that it works.
Was this helpful?
Thank you for voting!
Broken right END of oven door HANDLE (3 separate pieces assembled)
1 person found this instruction helpful.
  • Margaret from SARASOTA, FL
  • Very Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Wrench (Adjustable), Wrench set
(Followed the ORIGINAL manufacturer's instructions for assembly we retained when purchasing the appliance.) Replacing the broken handle end involved removal of the LEFT handle end as well as the broken RIGHT end, the center rod handle, and unscrewing the outer door face from the inner door face. Had to find specialty screwdriver for non-s tandard screw heads. Sigh. It was impossible to replace the door handle, as it requires removing the entire door - It is too heavy for one person to hold in place while the 2nd person tried to blindly replace screws thru a 1/2 inch slit in the outer and inner door pieces. Hiring a handyman is impossible leading up to the holidays, so we decided to just buy a new stove. Something that should be really simple to replace for less than $50 is now a major budget outlay due to a crappy design.
Was this helpful?
Thank you for voting!
Removal reinstalling
1 person found this instruction helpful.
  • Thomas from HAMPSTEAD, NH
  • A Bit Difficult
  • More than 2 hours
  • Screw drivers, Socket set
Removal old fashioned oven door handle took time after removing the oven door. New replacement handle was easy to install! Try to reinstall was long and finally got installed after 5 attempts due hinge on right side issue
Was this helpful?
Thank you for voting!
All Instructions for the MRMR
46 - 60 of 145