MLXG42RBW0 Tappan Washer Dryer Combo - Instructions

no problemO top loader. open top, disco two electrical plugs and a small hose, then remove two screws that hold valve in place and remove. Re install in reverse order. Thanks for your support Eliot in Alaska!

The leveling legs on my Frigidaire stackable washer & dryer were broken. They are made of plastic and while moving the unit one of the legs had broke off. I ordered two replacements from PartSelect and received them within a few days. The old legs were removed by screwing them out and then the new ones were installed. Pretty easy installa ... Read more tion for DIY. The new legs work great.

1. unpluged the dryer and turned off the gas.
2. pulled dryer out so i'd have ample room to work on it.
3. used large flat blade screwdriver in the front between the top lid and dryer face to gently pop-up the lid.
4. removed 4 screws from inside, that hold the face to the main box leaving the wires all intact.
Found ... Read more the coils on the lower left, held in place by two screws and plate.
5. took a good look at thier orientation before unpluging old and installing new, I recommend one at a time.
6. Vacuumm any exceess lint and check foam seal between lint trap and exhuast duc, the glue came undone on mine causing extra lint dust that is potentially flamable.
6. screw dryer front back on to main box, make sure to check wiring harness and that all electrical blade connectors are still pluged in to their componants.
7. At this point plug in, turn on gas and do a test run.
8.if everything checks out good then lower top make sure flexable exhuast hose is still connected on hte back of the dryer.
9. Tell your wife or girlfriend or husband or boy friend they can now finish your laundry :)

filter inalled

As others have described in more detail... I lifted the top, removed the 2 screws holding the front panel (one on each side, inside the control panel on either side - not the easiest to get at, but not too bad), popped the clips holding the front panel in place and removed it. With the front panel off, the location of the coils is obviou ... Read more s (lower left side). The only challenging aspect of this repair is that the 2 screws holding the coils in place are really torqued in so it was crucial to use the exactly correct size screwdriver and not let the screwdriver slip while unscrewing those screws. Actually swapping out the coils took seconds, of course they have to go in exactly the same way as the old ones. I did take a few minutes extra to vacuum out years of lint from the inside of the dryer. Overall, much easier and cheaper than I was expecting and now I know where everything is inside the cabinet.

Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!

Smelled burning rubber, checked belt. Belt was cracked and worn out. Easy repair. Removed front of the machine held together with two screws at the bottom of the unit. Removed top cover of machine (the part with the lid). It just pops off. Pushed tensioner wheel in and took off old belt. Putting new belt on was super easy. Working ... Read more like a champ now. $20 total with shipping. Not too bad to save a washing machine.

Pry up top from front remove 2 phillip screws at lower front panel slip belt under tub pulley then around motor pulley push belt tensioner towards back of machine slide belt onto tensioner pulley. (Done)

I push the new knob onto the post that fit the knob

Put machine on dolly. Tilted it on its back. Put screw driver into sheared leg and unscrewed broken leveling leg. Then screwed new leg in and tilted machine back up.

Placed new lint filter in proper slot.

I definitely would not have tried to do this had it not been for the other testimonials written here. But it sounded so easy, I had to just try it (the repair man estimated that with parts and labor, we would be looking at somewhere between $250 and $300!).

The repair itself took less than 15 min, but I spend a good deal of ti ... Read more me looking around the garage for a few screwdrivers and my socket set (me and tools don't meet too often). I could simply pry up the top cover on the dryer with my hands, then got it all the way up after removing two screws from the lint trap and undoing this really annoying wire connector thing. From there the front panel lifted off. To remove the drum, just had to release the tensonier on the belt, and it came right out. From this point it was really obvious where the replacement parts would be going. A few screws later, and I could swap the parts, and put humpty dumpty back together again.

It works!!!

I just popped up the top front using a large straight (slotted) screw driver, then removed the 2 screws at the bottom front, then the whole front panel popped down about a half inch to be lifted out of the way. I found the old drive belt way down under the motor (still attached as normal), very near the floor and removed the worn out bel ... Read more t by hand, and replaced it with the new belt by hand also. The spring loaded belt tightener- idler wheel makes this a very simple process to accomplish. Then, I replaced the front panel-- all done. Works like new.

unplugged machine. pried up with large regular screwdiver on top washer lid. removed two phillips screws bottom of front panel, had to use rubber mallet to drive front panel down to remove as was rusty and old. removed old belt using screwdriver. put new belt under tub pulley and put belt on small pulleys. kept moving tub and springs ... Read more by pushing on tub. Took several tries to get new belt to go on the large tub pulley but finally did it. I used the instructions you gave for replacing broken drive belt and it worked. replaced front panel and two phillips screws, put top back on and away it went.

Unplug from electric outlet. Use putty knife to press on two brackets holding the top cover. Raise top cover. Unscrew two screws holding the front panel. Raise front panel up and move to the right (careful with the wires). Disconnect wires from coils. Unscrew two screws holding a small bracket holding the coils. Replace coils and reassemb ... Read more le everything. (HINT: make sure you drum is empty. Mine contained dump clothes, and it turned out front panel actually provides support to the drum, so mine was hanging there with some weight in it - probably not good).