Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The heating element (Flat Can Heating Element 5400W, Heating Element, Whirlpool Dryer Heating Element, Dryer Heating Element) provides heat to the dryer. It is metal and measures 10.5 inches long, 7.5...
This thermostat (Dryer Operating Thermostat, Dryer Cycling Thermostat, Cycling Thermostat, Dryer Thermostat) is used to maintain a temperature of 155 degrees in the dryer drum. The internal bias heate...
The thermal cut-off (Dryer Thermal Cut-Off Fuse Kit, Dryer Thermal Cut-Off Kit) prevents the dryer from overheating when the dryer high limit thermostat fails in a closed circuit condition. This part ...
The drum support roller kit (Dryer Repair Kit) allows the dryer to tumble properly by supporting the drum cylinder. The idler pulley provides the tension required for a multi-ribbed belt. The belt att...
A dryer high-limit thermostat (High Limit Thermostat, Hi-Limit Thermostat, Dryer High-Limit Thermostat) is a switch that is actuated by temperature change. This high limit thermostat acts as a safety ...
This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. This part is sold separ...
This manufacturer-certified dryer lint filter is used to collect lint during the dryer cycle, to prevent damage to the machine and to prevent lint from sticking to clothes. This model comes in white a...
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so...
This OEM drive motor is designed to operate the drum in electric and gas dryers by turning the drive belt, enabling proper rotation during drying cycles. Compatible with most Whirlpool-incorporated dr...
This is a genuine OEM replacement rear drum seal for your dryer. This seal is made of felt and comes with the adhesive required for installation. The purpose of the seal is to prevent hot air from esc...
$42.12
In Stock
Order now and your part arrives by Apr 23
Questions And Answers for MEDC200XW1
Ask our experts a question about this model and we'll get back to you as soon as possible!
17 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jaime
December 16, 2019
Dryer not heating. What could be the problem?
For model number MEDC200XW1
Hi Jaime, thank you for your question. Looking at your model information there are a few parts that you should take out and test to see which one is giving you the issue. The first parts to check in this case would be all of your thermostats and thermal fuses. You can test those parts with a multi meter and they should be reading 0 ohms to be working correctly. If those parts are fine, you should then go on to testing your heating element as well. You can also test that with a multi meter and it should be reading between 0 - 50 ohms. Something else you should also check would be your filter and ducts. Make sure there is absolutely no blockage that would restrict air flow in your appliance. I hope that helps. Good luck with your repair.
4 people found this helpful.
Did this question help you?
Thank you for voting!
Ernest
January 23, 2020
Checked all fusses thermostat and heat element all tested good heating on hight heat cycle . Do i need to replace my timer?
For model number MEDC200XW1
Hello Ernest, thank you for your question. If the element, thermostats, and fuses are not the issue the timer would be the next part we would recommend replacing. I hope this helps.
3 people found this helpful.
Did this question help you?
Thank you for voting!
Bonnie
January 31, 2020
My dryer heats but takes long time to dry. Especially jeans average time 60 mins for 4 pair
For model number MEDC200XW1
Hello Bonnie, Thank you for your question. We advise checking the thermostats with a multi-meter. Both sets of prongs should read 0 ohms at room temperature. If your meter needle does not move or your display does not change, the part is bad and will need to be replaced. I hope that helps. Good luck with your repair.
1 person found this helpful.
Did this question help you?
Thank you for voting!
Clint
December 29, 2019
When I turn on my dryer it’s making a loud noise. Any ideas as to why? Thanks!
For model number MEDC200XW1
Hello Clint, Thank you for the question. Since we can not hear the noise we need a bit more of a description. Does the noise sound like a metal rubbing or a banging? Does the drum tumble and work normally and just makes the noise or is there just a noise and no tumbling? The more details to trouble shoot the better. Please submit a new question if you have any follow ups. We are looking forward to hearing from you!
1 person found this helpful.
Did this question help you?
Thank you for voting!
Clint
December 30, 2019
When i turn on my dryer it’s making a loud noise. The noise sounds like metal rubbing (there isn’t any banging) the drum tumbles just fine, but the rubbing metal sound persists and is very loud.Thanks
clint
For model number MEDC200XW1
Hello Clint and thank you for writing.
It certainly sounds like a faulty or loose drum support roller PS11752609, you should check for signs of damage, and replace it if needed. We hope this helps. Please contact us anytime.
To reach the heating element you only need to open the back cover of the dryer (about 8 nut-head screws). Remember to disconnect the power.
To remove the heating element there are two small nut-head screws. Remove the two electric wires. Then you can pull the heating element away.
You can check the heating element wi
... Read moreth an ohm-meter or visually inspect it to see if the heating element spiral wire is broken.
Don't hurry to dispose the old element. My model includes a small electric safety part. You'll need to transfer it to the new heating element (that comes without it)..
First tried heating element and thermal fuse with no luck. Ordered thermal cutoff and fixed problem. Had I used an ohm meter first I would have determined problem before having ordered heating element and fuse, as both had resistance. I wast just lazy and ordered the took the most common failed components first before taking dryer back
... Read more off.
The repair was easy. the most time consuming part was vacuuming the dust from the back of the Dryer, The repair required removing screw from the back panel of the dryer. Then removing screws from the heating element and unplugging the wires. The only moderately diffculy part was swapping the sensor form the old element.
