MAH2400AWW Maytag Washer - Instructions

First I looked up the error codes in the washing machine technical information pamphlet I got when buying the machine to determine what the problem was. It indicated that the machine wouldn't spin. After doing a few more tests I couldn't find the error code that was displaying, but the machine wouldn't run at all and just did a terrible ... Read more growling sound. I tilted the machine back to get access to the bottom. Undid the flimsy corregated covering held in by 4 screws. In the right front corner I found the pump. There were 2 tubs connected to the pump; I undid each (a simple squeeze off holder) and found nothing blocking either passage. The type of pump is build as one part, so I was unable to open it up.
I decided to order a new pump assuming that was the problem and in fact it was. Replacing the pump was a piece of case. I undid the two tubes, disconnected the electrical connector then removed it from the washer casing with 4 screws. The new pump was easy to install -- screwed it in place with the 4 screws, reconnect the electrical part (just a simple female / male connection), reconnect the 2 tubs, put the bottom covering back on, and that was it. It's working just fine now.

Unplug machine, turn on its side (have bucket to drain water from hose), unscrew drain hose bracket on back (so you can fully empty water still inside machine) unscrew bottom plastic cover, locate pump on left, pull out electrical connector, unscrew hose clamps, twist off hoses, unscrew pump and replace, and follow the above steps in reve ... Read more rse. I also made a coin trap from a sawed off plastic drain or downspout cover/protector and installed this inside the hose at the entry point to the pump, enlarging the holes enough to make sure they wouldn't easily clog with lint.

Removed hinge and all screws holding two halves together with glass between them put glass in new parts and replaced all screws hinge fits in there also
installed back on washer and away we went....

Simple 2x cross head screws remove water inlet pipe, 2 internal pipes with spring clips, 2 electrical connectors test for leaks and operation perfect

In this model the 2 main springs hang from a bracket built into the top of the machines frame. For some reason one of the pring was installed without the protective plastic grommet (called the guide spring washer). The handened spring eventually wore through the softer metal bracket due to the vibration of the washer.
The purchsed ... Read more plastic part fit into the bracket so firlmy that even with part of the bracket wore away it appears to be still strong wnough to support the weight of the tub. It has made it through 10 loads so far and it still working well.
Getting at the spring was easy but lifting the tub was heavy. Thanks - $4 part saved a $1000 washer.

I turned the washer on its side disconnected the hoses attached to pump. Then unscrewed the pump attatched to the washer base; undid the power source and ordered the part from you.
Reattached the new pump to the washer: reconnected the power source and hoses to the new pump. Then flipped the washer upright and it works.

got on internet found website that would show me how to get to the pump, part select phone number and the part number of drain pump- ordered on thurs night, got part on sat.am, me and my roommate tilted machine removed the 4 screws and 2 pipe clamps, did reverse procedure and machine was fixed- total repair cost was less than a service ca ... Read more ll

After two weeks with out a Washing machine in the RV, we were finally in a place long enough to order the part to fix it. I replaced this part before through Sears and although the price was similar,'it took two weeks to deliver the part. This was here the next day. One screw, two clamps and it was done.

Since this was our 3rd time to remove this part, due to coins getting stuck in the pump, it went pretty easily. Removed the panel underneath, removed and replaced the pump, replaced everything as it was. Washer works great again!

panel drawer cover required only one screw and the door cover had 8 screws to deal with but was really simple. Love the site!

Unplug washer (got zapped when first fiddling with it).
Turn off cold water at source and unscrew hose from washer
Remove two small screws to remove top of washer
Uncouple contacts from old cold water valve
Remove 4 small screws holding valve to washer
Remove old cold water valve

Install new valve and r ... Read more everse each procedure above.

Phillips screwdriver is only tool needed. There are about 14 screws around the perimeter, and my hand got tired, so I ended up getting my power driver to finish. Cleaned up all the surfaces while it was apart.

Took top off & disconnected each connection on the old control board assembly. Attached new one
to wiring. put top back on. Connected to water &
wash 1st load that night.

Undo screws two at the back, take the lid off disconect the pipes to the assy,a little tight for room if you have larger hands.Pipes have spring clamps. Undo screws holding the aasy, in front behind trim and screws at the top.This is the 5th time I have replaced this part the water lines clog up so there for water runs all over.

open up the back and listen to the noise then I fixed the problem I me Kevin Isadore the good job. thanks