This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on th...Read moree appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.
This white plastic washer door cover serves as the outer frame of a front-load washing machine door, providing structural support and protection for internal components. It fits securely over the inner door panel, helping to shield the appliance from dust, moisture, and external damage while maintaining a clean, finished appearance. Desig...Read morened as a direct replacement for cracked or damaged door frames, this part restores both function and aesthetics. Installation typically involves removing the door assembly and securing the new cover in place. Always verify compatibility with your specific model before replacement.
This water inlet valve assembly is for washers.
Water inlet valve assembly controls the water flow into the washer. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
Unplug the washer and shut off the water supply before installing this part. Wear work gloves to protect your hands.
This part is the replacement hot water valve for your washer. It is approximately 2-1/2 inches by 3-1/2 inches, and the valve head is approximately 1 inch in diameter. The hot water inlet valve in your washer connects to the water source and solenoid wires, and ensures the tub has the right amount of hot water entering it. If your washin...Read moreg machine continues to fill after it is full, or if it fills slowly, you may need to replace this valve. Another indication that your valve is damaged and will need to be replaced, is if you notice it is leaking when the washer fills up. Before you begin this repair, be sure to disconnect the water and power sources from your washer. This part is sold individually and is an authentic OEM part.
Also known as door boot seal or bellow. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Cali - For model number MAH2400AWW
February 26, 2020
Why does the washer make a really loud "crunching" sound when spinning in reverse? And how do i fix it?
Hello and thank you for writing.
There are several parts that could cause this and need to be checked for damage.
Drive belt PS2037087: Check to see if the belt is worn out, cracked, loose or bent. The noise could be a worn-out drain pump PS11741533, which makes a loud noise during the spin cycle or just as the cycle completes.
We hope this information helps. Please contact us anytime if you require further assistance.
Continually goes into suds code - tried several cleaning/extra water/vinegar quick fix type suggestions - no help. Use only he soap and reduced amounts. Takes hours to clear and finally finish cycle is there a sensor or other part that maybe causing problem.
Hi Paul,
Thank you for your question. If you have followed all of the steps to reduce the the amount of suds in your washer, there is a video listed on the Whirlpool website that may provide you with more information on how to resolve this issue. Here is a link to the webpage where you may find the video, https://producthelp.whirlpool.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/What_does_the_%22SUD%22_or_%22SD%22_Error_Code_mean. Here is a link from our website where you may also view your owner's manual, https://partselectcom.azureedge.net/assets/manuals/A3E524D17AF58F2965E78540AE636D417FC5A344.pdf. If you require more information, you will need to contact Whirlpool. Their telephone number is 1-866-698-2538. We hope this helps. Thank you and have a great day.
3 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Bob - For model number MAH2400AWW
January 28, 2020
Which control panel do I need for my model
Hello Bob, Thank you for the question. I looked up the part and it is listed as No Longer Available/Discontinued sorry. There are no part substitutions listed. Our suggestion here would be to call the manufacturer and see if they can provide you with a substitution for these part numbers. We hope this helps.
2 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
RD - For model number MAH2400AWW
February 8, 2020
When you power it on it goes into drain mode and the #1 shows up on screen and does not come on at all.. any suggestion???
Hi RD. This sounds like it may be a faulty door latch or control board. Thank you for your question and good luck with your repair.
2 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Bill - For model number MAH2400AWW
December 1, 2019
Washer does not spin
Hello Bill and thanks for writing.
If the washer won't spin or agitate the motor coupling might have failed. The motor coupling connects the motor to the washer transmission. ... If the washer won't spin or agitate, check the drive belt. If the belt is broken or if it isn't tight on the pulleys the washer won't spin or agitate properly. We hope this helps. Please contact us anytime.
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
Prev
1
2
3
Next
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer wouldn't spin / drain
53 of 60 peoplefound this instruction helpful.
Sarah from Kirkland, WA
Really Easy
Less than 15 mins
Screw drivers
First I looked up the error codes in the washing machine technical information pamphlet I got when buying the machine to determine what the problem was. It indicated that the machine wouldn't spin. After doing a few more tests I couldn't find the error code that was displaying, but the machine wouldn't run at all and just did a terrible
... Read more growling sound. I tilted the machine back to get access to the bottom. Undid the flimsy corregated covering held in by 4 screws. In the right front corner I found the pump. There were 2 tubs connected to the pump; I undid each (a simple squeeze off holder) and found nothing blocking either passage. The type of pump is build as one part, so I was unable to open it up. I decided to order a new pump assuming that was the problem and in fact it was. Replacing the pump was a piece of case. I undid the two tubes, disconnected the electrical connector then removed it from the washer casing with 4 screws. The new pump was easy to install -- screwed it in place with the 4 screws, reconnect the electrical part (just a simple female / male connection), reconnect the 2 tubs, put the bottom covering back on, and that was it. It's working just fine now.
Read less
Was this helpful?
Thank you for voting!
Coin ruined drain pum impeller blade / SUDS error
31 of 34 peoplefound this instruction helpful.
Dan from Arlington, VA
Easy
30 - 60 mins
Screw drivers, Socket set
Unplug machine, turn on its side (have bucket to drain water from hose), unscrew drain hose bracket on back (so you can fully empty water still inside machine) unscrew bottom plastic cover, locate pump on left, pull out electrical connector, unscrew hose clamps, twist off hoses, unscrew pump and replace, and follow the above steps in reve
... Read morerse. I also made a coin trap from a sawed off plastic drain or downspout cover/protector and installed this inside the hose at the entry point to the pump, enlarging the holes enough to make sure they wouldn't easily clog with lint.
Read less
Was this helpful?
Thank you for voting!
I leaned on the door while open and it broke off!!
36 of 65 peoplefound this instruction helpful.
Raymond from Fort Myers, FL
Easy
15 - 30 mins
Screw drivers
Removed hinge and all screws holding two halves together with glass between them put glass in new parts and replaced all screws hinge fits in there also installed back on washer and away we went....
My Orders
.gif "SUPPLEMENTAL INFORMATION Diagram and Parts List for Maytag Washer")
