M05B (V2) Frigidaire Freezer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Defrost heater shorted out.
6 of 6 people
found this instruction helpful.
-
William from Bay City, MI
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
Unplugged refrig., emptied freezer, removed ice bucket drive, removed back wall of freezer, used blower side of vac to defrost coils, remvoed glass heaters and pulled a chase line thru as I removed old wires. Replaced heaters and chased new wires using chase wires.
Was this helpful?
Thank you for voting!
All three lights are not working...lights are off but refrigerator still cooling. Also, the control box not lit up to show the temparture for freezer and refrigerator
7 of 10 people
found this instruction helpful.
-
Antonio from San Antonio, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.
Was this helpful?
Thank you for voting!
The Switch Broke...Absolutely Fell Apart.
5 of 5 people
found this instruction helpful.
-
Duncan from Metairie, LA
- Really Easy
- Less than 15 mins
-
Screw drivers
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
Was this helpful?
Thank you for voting!
freezer and fridg would not cool.
5 of 6 people
found this instruction helpful.
-
Dennis from Palm Ciity, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
Turn off power. unscrewed and removed the panel in the freezer compartment exposing the defroster(6 screws). pulled off the two defroster wires from their lugs. Removed the two plates (4 screws) holding the two heater elements. unsnapped the two heater elements from the plates. installed new heater elements. attached the plates.attached
... Read more
the two wires to the lugs.done
Read less
Was this helpful?
Thank you for voting!
Refrigerator Light bulb went out
7 of 12 people
found this instruction helpful.
-
ANGELA from MEBANE, NC
- Very Easy
- Less than 15 mins
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this helpful?
Thank you for voting!
Not defrosting
5 of 6 people
found this instruction helpful.
-
DON from CHANDLER, AZ
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Removed existing and installed the new part. The hard part is reaching to the back of freezer as it not very wide and is farily deep. Hard to get to arms in at the same time.
Was this helpful?
Thank you for voting!
Refrigerator light would not stay on
4 of 4 people
found this instruction helpful.
-
Dave from Manchester Center, VT
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.
reassembled the pieces.
Was this helpful?
Thank you for voting!
Light in my refrigerator didn't work.
5 of 7 people
found this instruction helpful.
-
Joseph from Byron Center, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved m
... Read more
e $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.
Read less
Was this helpful?
Thank you for voting!
Repaired Oven Range Light Bulb
3 of 3 people
found this instruction helpful.
-
Alan from SAN MATEO, CA
- Very Easy
- Less than 15 mins
-
Screw drivers
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this helpful?
Thank you for voting!
Raplaced switch
5 of 9 people
found this instruction helpful.
-
Winston A from Brooklyn, NY
- Really Easy
- Less than 15 mins
-
Pliers
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Was this helpful?
Thank you for voting!
lights wouldn't come on/work in refrigerator
4 of 6 people
found this instruction helpful.
-
Jane from Albuquerque, NM
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80..
... Read more
.would have been at least $100 to have a repair person come to the house!
Read less
Was this helpful?
Thank you for voting!
Ice Build Up On Evap Coil
4 of 6 people
found this instruction helpful.
-
bobbie from belleville, IL
- Very Difficult
- 1- 2 hours
-
Nutdriver, Pliers
Removing the old heater coil was a bit of a task as you need to take off all the brackets holding the heater coil and then remove the wiring from back of the coil. Installing the new heater coil assembly in the brackets and feeding the wirings back up to the top was a major task. Need to have long arms as the heater is located way back
... Read more
in the freezer compartment. The part was the exact match. The part was delivered in 2 days. Thanks alot. Will use your site again.
Read less
Was this helpful?
Thank you for voting!
dual light socket in fridge shorted out
4 of 7 people
found this instruction helpful.
-
Kimberly from Blue Springs, MO
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
took old socket out, ordered replacement part, dual socket no longer available. Turn off power to appliance, attach new single light socket, screw light socket and light socket holder back into place. Turned on power and it worked. No instructions included in packet, attached wrong first time, blew fuse, attached socket a different way
... Read more
, and it worked.
Read less
Was this helpful?
Thank you for voting!
Identifying the part on the parts diagram took the longest. Finding the screw driver bit that would remove the old screw that held the original shelf support took longer than the actual repair.
3 of 4 people
found this instruction helpful.
-
Lucien from Cambridge, MA
- Easy
- 30 - 60 mins
-
Screw drivers
Once I identified the bit that would remove the screw, the rest of the repair took 5 minutes. I removed the screw and discarded the remains of the original but now broken shelf support. With the same screw I simply attached the new shelf support that I received from PartSelect.com. End of story.
Was this helpful?
Thank you for voting!
Freezer and food compartment not working!! Warm.
4 of 7 people
found this instruction helpful.
-
David P. from DINGMANS FRY, PA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Spoke to Rep.Advised that several parts might be involved. Replaced 3 recommended parts and frig works like brand new. Saved hundreds of dollars in repairman costs.l. Plus $1000.00 for cost of new frig. If you can walk and chew gum at the same time? Easy fix. Very skilled Rep's!! Excellent service!! Great prices!! Highly recommend!!
Was this helpful?
Thank you for voting!