LWM204WC Amana Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
rinse cycle was not expelling the water
2 of 3 people
found this instruction helpful.
-
bert from coudersport, PA
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
remmoved the screws on the back that hold the panel on. removed the two hoses attched to the pump. removed three screws and pulled the pump out. spun the pulley and noticed no movement inside. looked closer at the pulley to notice it was broken. ordered new pulley online. received quickly. new part fit exacttly right. put three sc
... Read more
rews back in. hooked two hoses back up. put belt on pulley. plugged in and worked great.
Read less
Was this helpful?
Thank you for voting!
No belt and no motor gear
2 of 3 people
found this instruction helpful.
-
Matt from Hoboken, NJ
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers, Wrench set
Pop the top of the washer and use the nutdriver to remove the two screws holding the frontpanel on. Use the nutdriver for two more screws holding the plastic motor cover on. Use nutdriver for the two BIG screws holding the motorplate to the washer frame. After this, I literally beat/chiped/sawed the old motor geat off. Once that was d
... Read more
one, I put the new one on; had to use a hammer to knock it all the way on (try not to damage the clips). Reassemble everything. Flip washer over and place bet around two smaller gears. Rotate main tub gear to feed belt on. Make sure you use the nutdriver to loosen/tighten the motor positioner screws in the slots if things aren't working here.
The only really hard thing was taking the old motor gear off.
The only really hard thing was taking the old motor gear off.
Read less
Was this helpful?
Thank you for voting!
The washer was jumping all over the place and leaking water during the spin cycle
4 of 9 people
found this instruction helpful.
-
Elmer from Fort Campbell, KY
- Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
I took out the agitator first, then I took out the inner tub, next I took out the outer tub, and last I took out the transmission assembly. After replacing the snubber I put the transmission assembly back on, then the new outer tub and next the inner tub. Last I put the agitator back on.
Other Parts Used:
Was this helpful?
Thank you for voting!
Noisy on spin cycle
2 of 3 people
found this instruction helpful.
-
William B from STURGIS, MI
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Followed the excellent utube instructions you provide. Piece of cake when I followed the video. The rear springs became much more difficult because my model does not have rear access panel. They were the only stuggle. Thank you for doing the repair videos
Other Parts Used:
Was this helpful?
Thank you for voting!
tub overflowed
2 of 3 people
found this instruction helpful.
-
Ellen from Wilcox, AZ
- A Bit Difficult
- 1- 2 hours
Back of this washer did not remove, so we had to go in through the top--more restricting space. As you remove the old electrical metal contacts (two each of white and red), pay close attention to where they connect properly. Best to mark them so as not to confuse how to place new contacts. Also, we disconnected a white plastic hose on
... Read more
opposite side of top which determines load size and amount of water, so be sure to look for this.
Read less
Was this helpful?
Thank you for voting!
Little Cold Water Flow
2 of 3 people
found this instruction helpful.
-
David from Lexington, KY
- Easy
- 30 - 60 mins
-
Pliers, Socket set, Wrench (Adjustable)
Unplug power cord; turn off hot and cold water supply; remove water hoses from machine; open top of machine by prying lid open; remove two hex screws holding water inlet valve in place; remove hose from top of old water inlet valve; remove 4 wires; connect bottom set of wires (red and white) to new water inlet valve; reinstall water hose
... Read more
to top of new water inlet valve; install new water inlet valve onto machine using same hex screws; connect remiaining red and white wires; install hot and cold water hoses to machine; turn on water supply valves at wall; reconnect wall plug; turn water type selector to cold, pull out timer and watched the water flow full-force for the first time in 2 years! Have wife give you a hug for saving cost of new washing machine!
Read less
Was this helpful?
Thank you for voting!
Noise
1 person
found this instruction helpful.
-
Marylou from Old Forge, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Wrench (Adjustable)
I changed the piece easily
Was this helpful?
Thank you for voting!
Spin cycle out of Balance - Machine walks from wall
1 person
found this instruction helpful.
-
Needham from Leesville, SC
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Disconnect Power. Disconnect supply hoses. Open top by releasing top retainer clips with a thin blade or putty knife. Remove 2 sheet metal screws retaining front cover. Remove front cover. Lay a blanket on the floor and lay the machine over on its side leaving access to the front where the panel was just removed. Take belt off. Remove pu
... Read more
mp hose at bottom of drum. Prop up drum so it is centered in its normal position and not laying to one side. Do this near the lid end. Remove all centering springs - carefully. Drum and transmission assy will now come out through the front opening. Flip drum assy upside down with transmission up. Loosen the screws (do not remove completely - WARNING OF 200 LBS SPRING LOAD!) that clamp the snubber ring to the transmission. Remove the old snubber ring and replace with new. Be sure it is completely under the flange all the way around. Tighten the retaining ring screws. Reassemble all parts in reverse order. Done. Be sure to level the machine per owners manual instructions.
Read less
Was this helpful?
Thank you for voting!
Washer making noise during cycles
1 person
found this instruction helpful.
-
Nat from Baton Rouge, LA
- Really Easy
- 30 - 60 mins
-
Nutdriver
I moved the washer out from the wall. unplugged washer, turned off water. Took off rear plate exposing pump. Disconnected hoses, using dry/wet vac to catch water. Took out three screws holding pump to base of washer and removed pump, belt slipped right off. Set new pump in place and put in screws. Connected hoses, put rear plate back on.
... Read more
Tilted washer back and installed belt on pulleys and motor. Turned on water, plugged in washer, started to wash clothes. Washer works fine and QUIET. I have yet to find the model number on my Maytag washer. I ordered the pump by sight (good pics).
Read less
Was this helpful?
Thank you for voting!
Wouldn't spin after rince
1 person
found this instruction helpful.
-
joe from LAWRENCEVILLE, NJ
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Followed the great instructions on your video
Was this helpful?
Thank you for voting!
Broken belt needed to be replaced.
1 person
found this instruction helpful.
-
Niels from Hopewell Junction, NY
- Easy
- Less than 15 mins
-
Socket set, Wrench (Adjustable)
Replacing a belt on a washing machine is a pretty easy process, depending slightly on how easy it is to access the belt. On our Maytag, the belt can be accessed directly underneith the washing machine. So, I lifted the front of the machine and put a few blocks of scrap wood under the legs to hold up the front of the machine. Once that
... Read more
was done, there was nothing else that needed to be removed to access the pullies that the belt had to go around. The motor itself is generally adjustable to allow the belt to be changed. So, I first wrapped the belt around the largest one that spins the washin machine tub, and then wrapped it around the one that spins the water pump. Finally, I loosened the bolt on the motor to allow it to move, wrapped the belt around the motor, pulled the motor back to tighten up the belt, and tightened the bolt that holds the motor in place. It's a pretty straight forward repair that narly anyone could do thmselves.
Read less
Was this helpful?
Thank you for voting!
Locked up the machine.
1 person
found this instruction helpful.
-
Mitchell B. from Moreno Valley, CA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers, Socket set
Unhooked the macine pulled out for easy access .removed drive belt rear cover plate ,vaccumed remaining water out thru drain hose with wet and dry vac. Removed hose clamps and hoses .removed the three hex screws holding the pump to the base plate. The removed the old pump , Installed the new pump hoses access plate and belt . Hooked the
... Read more
machine up . Worked perfect.
the
the
Read less
Was this helpful?
Thank you for voting!
Washer made horrible noise when entering the spin cycle.
1 person
found this instruction helpful.
-
Lance D. from Broken Arrow, OK
- Easy
- Less than 15 mins
-
Nutdriver, Pliers, Socket set
I removed the cover on the back of the machine, detatched the 2 hoses and removed the 3 screws holding in the Vertical Style Pump - with pulley. These screws are 10 mm nut-driver. The cover if I remember correctly was a standard rather than metric so make sure you have both available.
Screwed new part in, re-attached hoses an ... Read more d replaced cover. The last step requires strength to hold the machine up and re-configure the belt. This is best accomplished by looping it onto the tub and the pump first, the using the tub pulley to maneuver the belt onto the motor.
Only discouragement was that it took 8 days to receive the part as the first shipment was not the correct part at the fault of the distrutor.
Screwed new part in, re-attached hoses an ... Read more d replaced cover. The last step requires strength to hold the machine up and re-configure the belt. This is best accomplished by looping it onto the tub and the pump first, the using the tub pulley to maneuver the belt onto the motor.
Only discouragement was that it took 8 days to receive the part as the first shipment was not the correct part at the fault of the distrutor.
Read less
Was this helpful?
Thank you for voting!
pump bering failure
1 person
found this instruction helpful.
-
Robert from Englewood, FL
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
first i removed the front panel unclamped the hoses unscrewed the 3 screws that hold it in pulled it out, opened the new one and actually dropped it in and it fell into place with the holes lining up inserted the screws and hose clamps and reinstalled the belt which fell off when the old pump was removed, put the front back on and gave it
... Read more
a test then let the wife do a load of wash it worked like new
Read less
Was this helpful?
Thank you for voting!
water leaking from under front of washer
1 person
found this instruction helpful.
-
Mark from Isom, KY
- Really Easy
- Less than 15 mins
after doing some research I found out that a loose or slipping water pump belt could cause the water pump to not pump out the water correctly. Under the washer is the belt. All you do is have someone lift the front of the washer up enough that you can reach under and remove the belt. Then replace the belt back like you took it off.
Was this helpful?
Thank you for voting!