EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

LWM204WC Amana Washer - Instructions

All Instructions for the LWM204WC
31 - 45 of 281

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oil leak from lower lip seal
6 of 6 people found this instruction helpful.
  • Anthony from CHESANING, MI
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set, Wrench set
I didn’t have special tool for brake but punch and hammer worked. Seal was easy to replace. Several videos online to show you how. It wasn’t worth it to tear apart the transmission and buy more parts/seals (if they were even available). But I didn’t know how much oil was in it. I drilled a hole in the side to somewhat check level and added 80-90 gear oil. It was almost empty and added almost a quart. Used a self taping screw/bolt with gasket sealer to plug the hole. I got 34 yrs out of this washer. If it fails, oh well. Just hate to buy a new one that only last 10yrs if im lucky.
Was this helpful?
Thank you for voting!
washer was squeeling to a stop
7 of 9 people found this instruction helpful.
  • paul from newbern, TN
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
first remove drive belt then then remove dust cover on bottom of shaft take 5/16 nut driver to only 4 of the screws off that hold the brake cover on install 4 5/16 screws 1" long in those 4 spots.reomve rest of screws then slowly reomve back out 1" screws to relve spring pressure from brake pad.install all new parts from partsselect.com then install other part taken off in oreder and make your wife very happy
Was this helpful?
Thank you for voting!
Washer went off balance and the flume broke off
13 of 27 people found this instruction helpful.
  • Michelle from Jupiter, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I removed the part that was still attached to the washer and installed the new flume. It took less than five minutes and a repair that would have cost over $85 cost less than $10 and I am no plumber!
Was this helpful?
Thank you for voting!
new belt worn out by a bad motor pulley
7 of 9 people found this instruction helpful.
  • ALBERT from WASCO, CA
  • Really Easy
  • Less than 15 mins
  • Pliers
i took off the old belt and i took off the motor pulley with the pliers and srewdriver. i put the new pulley in with my hand and gave it a hit with the palm until it snap in and then i put the belt on by rotating the main pulley on tub till the belt was pulley on.
Was this helpful?
Thank you for voting!
Noticed nick in drive belt durng inspection and cleaning
5 of 5 people found this instruction helpful.
  • Brian from Plainville, CT
  • Really Easy
  • Less than 15 mins
Washer was making noise especially when spinning. I took the washer apart to clean it, That is what it really needed. Also adjusted the water level to prevent overflows which caused soap and water to get underneath into the drive belt area as well. During inspection noticed a nick in the drive belt, Although this was not really causin g immediate problem wanted to repalce it to prevent problems. Ordered the belt; it came in two days with no special postage. To install, just leaned the washer over on its front on a slight incline. Took old belt off and put new on by turning the big pulley. It is spring tensioned, so no tools. This may be the easiest part repacement I ever did. Took longer to write this paragraph than to repalce the belt.
Was this helpful?
Thank you for voting!
No hot water was making it into the laundry cycle.
6 of 8 people found this instruction helpful.
  • Neil from Ann Arbor, MI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Wrench (Adjustable)
First I unplugged the machine, then turned the water supply off in order to disconnect the hoses at the back of the machine. Next I pulled the top up and leaned it back so I could access the water valve at the rear of the machine (You might have to use a screw driver to pry the top off the pins which hold it down in front...). I then un screwed the the valve and disconnected the wiring and, in order, re-connected to the new valve. Now reverse and turn on the water and yes, the new valve fixed the hot water problem. We can now do the "whites".
Was this helpful?
Thank you for voting!
I had water leaking from the top of the tub.
6 of 8 people found this instruction helpful.
  • Lester from Elk Grove, CA
  • Really Easy
  • 15 - 30 mins
I opened up the top of the washer which exposed the tub, I took the top ring off the tub and under in side of the ring is the seal. Took the old one out and put the new one in. The old seal was completely wore out.
It was real easy.
Finding the part is usually the hardest part, but thanks to Parts Select finding the part was the easiest part of the repair.
Was this helpful?
Thank you for voting!
No hot water on wash or rinse cycles
5 of 5 people found this instruction helpful.
  • James from Buffalo Grove, IL
  • Really Easy
  • More than 2 hours
  • Nutdriver, Screw drivers
I read some stuff on the internet where folks with the same problem replaced the water inlet valve to repair this same problem. So I did the same. However, after I installed the new water inlet valve, the problem was still there. It was at that point I decided not to guess at the what issue was and instead test the components in the wa sher. Yes, I am a lazy dumb ass. There are many of us out there. I decided to use a continuity tester to test all components in the hot water fill circuit and determined that the water temperature switch was bad. So I ordered a new switch from Parts Select (they rock - it showed up next day) replaced the water temperature control switch and...walla. fixed!!! Only took about 30 minutes to replace. Lesson learned: Don't be a dumb ass and guess. Test.
Was this helpful?
Thank you for voting!
broken pump, burned belt
5 of 6 people found this instruction helpful.
  • Jeffery from Omega, GA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Socket set, Wrench set
I removed four screws to remove a plate to get access to the pump. Then I removed 3 screws to remove the pump. I then put the new pump in place and put the 3 screws back in the pump. Then I put the plate back on and put the 4 screws back in. Then I put the belt on and put the washing machine back in place and connected the water line s and drain line and plugged the washing machine back in and then tested the washing machine to make sure it worked. Job completed.
Was this helpful?
Thank you for voting!
washer overflowing
7 of 12 people found this instruction helpful.
  • Aaron from Lawton, OK
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Once the washer was unplugged, i removed the two screws on the back pannel, disconnected the three wires, rubber water line, and two screws holding it to the control panel. Quite simply reversed the process with the replacement part i ordered, which arrived overnight, and the problem was solved.
Was this helpful?
Thank you for voting!
Water pump failure
5 of 6 people found this instruction helpful.
  • John from Alhambra, CA
  • Easy
  • Less than 15 mins
  • Nutdriver, Pliers
Disconnect electricity....remove front panel by gently prying up lid.... Remove two small screws at corners of front panel. You may need small nutdriver here or very small hands, you can easily swivel tub out of the way....once front panel is off water pump is at the bottom right... It is only connected by two squeeze clamps and 3 nuts... This is obviously where the adjustable wrench and nutdriver come in very handy... Otherwise this job will be a bit longer....be prepared for residual water to pour out...you will need towels or a bucket....replace old with new one by reversing the process...at this point tilt the entire washer on it's backside or at least at a 45 degree angle to access the bottom... Swivel the motor away to slack up the belt...remove belt and replace in reverse order of diassembling.... Should take no more than 15 minutes.... Good luck!!!!!
Was this helpful?
Thank you for voting!
Washer was making noise during spin cycle
4 of 4 people found this instruction helpful.
  • William from MORGANVILLE, NJ
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
Hardest part was finding part that needed the needed repair. Searching the web for issues associated with the sound resulted in many links. Once the sound was found, I went to the video to see how to remove the Water Pump so I could examine it to confirm that was the correct piece. It took about 15 minutes to remove the part. Since I h ad to remove the belt to get it out, I realize that the belt needed replacement as well. So both parts were ordered. Replacing the parts also took about 15 minutes. Relatively easy repair. Be aware that the video on the part select video shows the water pump in a different location than the Maytag washer. To get to the Maytaq water pump, there is a panel in the back that had to be opened to access the water pump.
Was this helpful?
Thank you for voting!
Washer always going off balance full loads or small
3 of 3 people found this instruction helpful.
  • Jeffrey from HONEY BROOK, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Socket set, Wrench (Adjustable)
I tilted top cover to remove front washer panel removed suspension springs to remove complete tub assembly to gain access to bottom. Drive pulley to remove snubber ring I performed the repair step by step as per your video. was dead on made the repair go smoothly. I installed the belt last tilting washer mechine back to gain access to und ercarrige just walked belt on all three pulleys self adjusting then. made sure washer was level. Front to back side to side no rocking in any deriction My wife did four full loads problems gone I think all needed to be done to complete repair snubber ring , washer drive belt, & leveling machine all played there roll in putting washer back in factory working condition washer not a angery walking vibration nightmare
Was this helpful?
Thank you for voting!
White fluffy residue appeared under washer. Unbalanced banging during spin cycle
4 of 6 people found this instruction helpful.
  • John from Blue Bell, PA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Parts needed: Snubber Ring and 6 Springs (don't put the old springs back)
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to rem ove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.
Was this helpful?
Thank you for voting!
Leaking water inlet hoses.
4 of 6 people found this instruction helpful.
  • Helen from NASHUA, NH
  • Really Easy
  • 30 - 60 mins
Removed the old hoses and screwed on the new hoses.
Was this helpful?
Thank you for voting!
All Instructions for the LWM204WC
31 - 45 of 281