LWM201H Amana Washer - Instructions

Raised washer. Identified problem. Removed from panel, gaining access to drain pump. Removed hoses, replaced pump. NOTE: I used blue Loctite on pump mounting bolts. Reinstalled from panel, lowered washer, cleaned drum. Ran one (1) cycle with hot water and bleach ONLY.

Tilted washer back and removed belt
Lifted front of top and propped up
Unscrewed two screws and removed front of washer
Disconnected two drain lines from tub
Disconnected 6 springs from tub
Removed tub
Popped off bottom plastic cap
Removed locking ring
Slid off gear from shaft
Unbolted screws f ... Read more rom snubber support ring
replaced snubber
Put everything back together in reverse order

Worked like a champ!!!!!

Turned it over to my 35-year old son who removed pump and pulley assembly and the old drive belt, then simply replaced with new assembly and belt from PartSelect! Could not have been easier - from my viewpoint.

The Clamps for the hoses were difficult to get to, otherwise was a simple replacement job, involving clamps and screws and bolts.

Had wife balance washer on front edge while I accessed working parts from bottom of washer. Removed drive belt and turned agitator pulley, transmission pulley and drain pump pulley by hand. Drain pulley hard to turn and shaft had play in it. Ordered new drain pump and replaced upon receipt. Very few fasteners to remove and replace pum ... Read more p assembly. Drive belt was easy to remove and replace. Recommend also replacing drive belt on a washer this old.

Troubleshoot problem, removed front, removed drive belt, removed pump with pulley. Note, new pump did not have black plate, installed worked great.Thanks

I had to raise the top of the washer and take off the front pannel. It was not too hard to replace the pump except that it was in the back corner and it was hard to reach the bolts to remove and install the new pump.

Laid washer on its side, released five of the six tub springs, then removed the dive belt and the main pulley. With some effort removing the old snubber ring, placed the new snubber in place. After fighting with the large spring under the pulley I was able to replaced the six screws with the help of an assistant. Replaced the pulley, b ... Read more elt and the five springs. Closed the unit up and placed all the hoses back in place. I was amazed at how smooth the washer functioned with no vibration at all! Thank You.

I found on-line that replacing the snubber ring may fix the problem and ordered the part. With the instructions also downloaded I started taking the washer apart. Without the instructions the task would have been more difficult and possibly disastrous as I might have taken the bolts out that tighten down the snubber ring. All went well wi ... Read more th a little patience. The washer works good.

open top,remove back panel.then laid on the side and removed belt.remove hose from tub to pump.removed small hose for fill level.Hard part was to remove springs from tub.Then pull tub and transmission out of housing.Remove pulley from shaft.Lossen screws around snubber ring but do not remove them.Remove old snubber ring.clean surfaces wit ... Read more h alcohol.install new snubber ring and assemble in reverse order.

I removed the back panel and then removed the old pump. After attaching the new pump I flipped the machine and attached the new belt. I put everything back together and voila, the machine works.

this email does not include the rest of the parts i ordered. i had to replace the pump and the base panel of the washer as it was rotten. i had to open the top, remove the front panel and change out the base and install the pump. your parts and website were very helpful. thank you however this will be the last maytag i will purchase ... Read more .

We're not repair people. So when calling around for the replacement belt no one had it. Everyone said that the belt went to a dryer. We simply inspected the machine. Located the worn belt which was on the bottom of the washer machine went online and ordered the belt. Thank you so much you guys really saved me. I will always recommen ... Read more d you all to everyone that I know. Your system works Great! Thanks Part Select!

I got the part the very next day, very easy to replace. Replaced the belt as well. Parts Select is the best. Vert straight forward repair.

I turned washer over, took off old shredded belt. One of the pulleys is spring loaded so I just held it in as i looped the new belt on. Easiest repair I have made on a washer!