LWM201H Amana Washer - Instructions

took off back small metal panel, tilted washer front side down, easy to put into place after removing old part

Because I live alone, the washer is very heavy so I just used some sliding robots under the legs of washer so I could slide it out from the wall by myslef after removing the small plate in the back to accfess the water pump I used the nut driver to remove the 3 screws holding the pump in place, but I used the pliers to remove the 2 water ... Read more hoses first then I mounted the water pump back into place, installed both hoses again then I tilted it back against the wall while re installing the belt then I pushed it back against the wall and removed the sliders so I could make sure it was back level this was a very easy repair even if you never fixed any thing before the belt replacement was even more simple to replace because the motor is springloaded so you just had to pull on it enough to remove it from the pulleys

I ordered the replacement pump assembly (water pump)for my Atlantis model maytag washer, removed the old one, installed the new one and works like a charm. The only difficulty I had was trying to figure out how to remove the cover on the front of the washer, to remove the clips, it slid side to side instead of popping out, found the inst ... Read more ructions on-line, NO instructions came with the pump but if you have any common sense when it comes to repairs it was easy to remove and install the new part.

I first opoen the front panel of the washer. That was a bit tricky. Had to slide a thin blade between the top of the washer and the front panel, pushed in to release the "clamp" and gently raise the top, it hinges on the back.
The rest was undoing three bolts, refit the new pump and put the belt back on.
The part cost me less ... Read more then $65.00.
The repair estimate by the local repair man was $ 250.00.
I am very happy.

Thank you PartSelect.

Andre M. Roberty

Unplugged electrical plug. Disconnected water and drain hoses. Turned washer on front side. Removed old belt from bottom of washer. Removed pump access panel. Removed old pump. Installed new pump. Torqued pump mounting screws 1/4 turn with socket wrench. Installed new belt. Put on pump access panel. Hand tested motion of belt and pulleys ... Read more for smooth travel. Put drain hose on. Turned washer in the upright position. Reconnected water hoses. Washer works like new.

Spoke with a trusted repair man, described the problem best as I could. I smelled a burning rubber smell. Got on Internet for troubleshooting problems, 77% likely a drive belt. BINGO! Ordered a new belt, took old one off, cleaned the pulley ( it had burnt rubber stuck on it, difficult to remove) lightly sanded pulley just so it would be r ... Read more eally smooth. replaced belt. Magic, it worked. I am no repair woman, but carefully listening and explaining helped. Oh, belt is under the very bottom of machine. Very easy to get to, just tilt back and lodge at an angle and make sure it doesn't move.

Unplugged everything, disconnected hoses, took belt off and put new one on.

Unbolt old pump with three bolt from top of pump inside the washer. Use needlenose pliers to remove intake and output hoses from old pump. Remove belt from pulley under washer. Reverse procedure to install. I was worried because there were two pumps listed for this model number, one being $95 and the other being $40. I bought the cheaper ... Read more one and prayed. It worked just fine. Fixed a $500 washer that was on it's way to the dump and made $100 in the process!

Removed back plate, tilted up washer removed pump removed belt. Then replace pump and then replaced belt

tilted the machine forward, worked off the old belt and put the new belt back on. no tools required, done in less than 5 minutes.

All i had to do was pull the washer machine from the wall and lean it back as far as i could and get under it and place the (DRIVE BELT) on the two smallest pulley then put the belt on the large pulley and my work was done it was very simple and easy.......

Leaned the washer back and propped it up and changed the belt. This is the first time ever repairing an appliance. I feel very good about myself as I am 49 yrs old and did not have to call a repairman for this.

I pulled the washer away from the wall so that I could lean it back at an angle. I removed the old belt and put the new one on. I started with the smaller pulley first and put the belt into the groove. Next I went to the next larger pulley and did the same thing. Then I went to the largest pulley and started to put the belt into the groov ... Read more e and started turning the pulley by hand. The belt went right on.

pulled out the washing machine that was the hard part, tilted it back checked too make sure everything spun by hand just to see if that was reason for the belt to snap but everything spun by hand nice and smoothly poped on the drive belt and everything works fine back in business.

First I am a woman and was able to do it, and if I can do it anyone should be able to do this. The service call alone was 75.00, and the belt was 23.00 with shipping. First we tilted the washer at a 45 degree angle and I removed the belt, and just rolled the newer one on the track. That was it and I was done. My washer now purrs like a ki ... Read more tten love it. And Part Select sent out my part and I recieved it next day, thank you for wonderful service that kind of service is hard to find. <3