Models > LSD2615HEW > Instructions

LSD2615HEW Admiral Refrigerator - Instructions

All Instructions for the LSD2615HEW
1 - 15 of 898
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
light on to order water filter
Pressed in the end of the filter cover, lowered it down part way. Twisted the old filter 1/4 turn and removed it. Set in the sink to drain. Inserted new filter and twisted it to lock. closed cover. Done. Total time @ 1 Minute.
Parts Used:
Refrigerator Water Filter
  • Douglas from Byron, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
901 of 1017 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of connection held the other two attachment points along the long edge of the icemaker. I did not have repair manual or useful drawing but looked @ PartsDirect pic of side brackets & used a small mirror to confirm that mine were also some sort of "snap in" attachment.
Remove icemaker unit by pushing upward and outward on the unit. I takes a good bit of pressure and will pop loose, but be careful not to break attachment bracket from freezer wall.
Scavenge shut off bar and wiring harness from old icemaker once you have it out & attach to new one before installing it back in freezer.
Again, you might find a mirror useful to align those pesky snap-in brackets with the new unit.
Since you probably kept your freezer running while waiting for the part, the plastic snap-ins will be cold and brittle. I warmed them up first by applying a dampened cloth heated in the microwave to make them a little more pliable.
A good push of the new unit towards the snap-ins along with some upward force will get it stable.
Reattach the metal screw in bracket & connect the wiring harness to rear plug... and don't forget to plug the whole thing back in.
It will take awhile for the first batch of cubes dump as the timer may need to cycle completely around to get to the fill cycle... be patient.
Dump the first couple of batches of cubes just to make sure you're free of any residue.
Parts Used:
Replacement Ice Maker
  • Bernie from Diamond Bar, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
805 of 893 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker leaking at first then quit making ice all together
unplugged refrigerator and shut off water, removed one screw and loosened two more, after removing one side of the ice bucket rail, unplugged electrical from old ice maker. Then I removed the bail and out on new one, reinstalled ice maker in reverse order from taking it out.
Parts Used:
Refrigerator Water Filter Replacement Ice Maker
  • Hootie from Joshua, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
427 of 485 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The compressor would not run.
I removed the screws in the lower back panel where the compressor is located. Then I unplugged the capacitor and plugged the new one in. I then checked to see if the compressor would start. It wouldn't so I replaced the overload relay with capacitor and that fixed the problem. The capacitor just plugs into the relay then plugs into the compressor. There are several screws but all in all it is easy.
Parts Used:
Compressor Start Device and Capacitor Run Capacitor
  • Gilbert from Clinton, MO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
325 of 371 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water overflowed ice maker turnning ice bucket into solid mass of ice
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: one of the three screws that hold the ice maker to the refrigerator wall is hidden behind the large (black) end of the ice maker and is difficult to access. Before trying to replace the ice maker, make sure you have the physical dexterity to remove that screw. Second problem: it is not apparent how to remove the wire harness that plugs into the ice maker assembly. BEFORE you can remove the wire harness, you MUST remove the large white cap that covers the black end of the ice maker assembly and then push in a retaining tab to release the wire harness. If you don't do this, the wire harness will not release. Other than those two problems, it was relatively easy to remove three screws, unplug the wire harness, transfer three small, metal parts from the old ice maker to the new, plug in the new wire harness, mount the ice maker assembly so that the water tube is in the proper position, and then re-install the three screws. The ice maker works fine now. (P.S. I was told by an expert that the real problem might be a malfunctioning fill valve. I would have replaced the fill valve if replacing the ice maker assembly had not fixed the problem.)
Parts Used:
Replacement Ice Maker
  • Harry from Grand Ledge, MI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
273 of 372 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker was leaking water and causing ice globs in ice bucket.
Parts were available at the locat applicance store, but the cost was 20-25% higher than ordering through Parts Select (including shipping) + it was delivered in 3 days right to the house.

Removing and replacing the ice maker was fairly straight forward. Tight quarters to work in, but managable.

1. With the freezer turned off, uplug the ice maker power cable at the back of the freezer.
2. Remove the four phillips head screws and ice bucket rail to the side of the freezer. I found it was easier to re-install the new ice maker with the rail clear off.
3. Loosen the two upper hex head screws holding the ice maker (requires a nut driver).
4. Lift the ice maker up and off of the upper screws.
5. With the ice maker out of the freezer, remove the power cable from the old ice maker and re-install on the new ice maker. At this point, both the front cover and the on/off lift bar can be transfered from the old ice maker to the new one.
6. Slip the new ice maker down over the two upper screws making sure the lower mounting tab is behind the ice bucket rail. Make sure the hole on lower mounting tab lines up with screw hole.
7. Re-install the ice bucket rail and tighten all screws. Make sure the water supply tube is lined up correctly feeding into the ice maker.
8. Re-connect ice maker power cable at the back of freezer and turn freezer back on.

It took about 4 hours for the first ice to generate. It cycled normally after that. No more leaks or ice globs in the ice bucket.
Parts Used:
Replacement Ice Maker Ice Bucket
  • Stanley from Cortland, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
210 of 230 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Removing the existing filter by rotating as directed and then dislodging from 'docking' station proved difficult. Turns out, the old filter is under a bit of vacuum pressure and getting the unit to separate or release was a challenge.
I removed the drop-down outer housing by gently prying the sides of the two pivot pins at the rear. This gave me move 'room' to grip and slightly rotate then pull the old filter forward and away from the tight suction connection. I was concerned that I would be too forceful for the plastic assemblies and would break something; deliberate motions and a steady thought process on the problem helped disengage the darned old filter!
Parts Used:
Refrigerator Water Filter
  • Jake from Novato, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
212 of 325 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed to change water filter in refrigerator
The switch-out of the water filter was simple with good instructions on the box.
The part was delivered very, very quickly!
Parts Used:
Refrigerator Water Filter
  • Marilyn from Lilburn, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
160 of 249 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water filter needed replacing
I unscrewed the old one and replaced it with the new one. The real benefit was I got the exact part I needed w/o a 30 minute drive and sales people that ignored me. I had gone to the local store the day before and come home with the wrong part because i could not get assistance and the part # I had did not match what was labled on the package. I used the same part # on the website and got exactly what was needed, less that 48 hrs after I ordered it. thanks for the prompt service. we will be a repeat customer
Parts Used:
Refrigerator Water Filter
  • Kathryn from Cedar Springs, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
111 of 123 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Trickle to no water from dispenser / very little ice
Shutoff water and turn off fridge. Remove the main water hose from the fridge with pliers, then remove back bottom plate of fridge where the hose was at (about 5 screws) in order to disconnect the hoses going into the valve by pushing in on the plastic colored fastener(blue & white) while pulling on the hose at the same time. Do this for each of the hoses. Then disconnect the wires from the valve and unscrew the valve(1 screw) from the back plate. Replace with new valve which comes with brand new fasteners for the hoses so all you have to do is insert the hoses in the valve and reverse the above process to install the valve.
Parts Used:
Dual Water Valve
  • Salvador from McAllen, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
113 of 132 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Bearing Cup Assembly was broken and ice would jamb against it during the ice making cycle.
I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing the front cover which is snapped in place, then removing two recessed screws at the front. I removed the broken part, I then reassembled the ice maker with the new part. I replaced the two recessed screws at the front and snapped on the cover. Then I reinstalled the ice maker in the refrigator by plugging in the harness, slipping the ice maker over the loosened screws in the refrigerator and replacing the screw that was removed from the underside bracket. Tightening all the screws completed the project.
Parts Used:
Water Fill Cup and Bearing
  • David from Chester, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
107 of 133 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door would not close
After emptying the refrig. door, I unscrewed the plate on the top of the refrigerator that covered the door bolts. Then off with the three bolts. I removed the door by lifting it up a few inches. The two parts of the door cam were easily removed and replaced with the new part. BEFORE REPLACING the door spread vasoline on both cam parts.
(Not after as I did. The second time you do any of these repairs go SO much better :o)
After putting the door back on, adjust the tension of the screws holding the door in place if needed to align the door on the cams so that it shuts completely. Failure to do this will require taking the top off the door again. (see comment above on "... second time...")
If all is properly aligned, the door should swing completely shut.
Even with the mistakes that required removing the door to lubricate the cams, and removing it AGAIN to readjust the screws on the top to properly align the door on the cams, this was a twenty minute job. My wife and I were still speaking to one another at the end of it- a sure sign of an easy repair.
Parts Used:
Door Closure Cam Kit
  • Russ from Asheville, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
79 of 84 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
not making ice
Installed new ice maker. It was easy - loosen two screws and unplug old wire harness. Put new unit in place. Did not realize new unit would not come with wire harness, but transferred old one to new ice maker (easy) and, "voila" some ice in 24 hours -- much ice since then. I am a 68 year old woman and it was "sort of fun" doing this job.
Parts Used:
Replacement Ice Maker
  • Pat from Dallas, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
77 of 91 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No ice in ice trey
The easiest thing to do was pull the ice make off. After taking the 3 screws out of the wall of the freezer, take a screwdriver (flathead) and push on the tab for the electrical plug and wiggle the cord out. Then you can take 3 screws out for the main cover and another 2 screws on the next cover. There's the part, pop it out and replace holding pins and start the process of putting back together the opposite way you took it apart.
Parts Used:
Cycling thermostat
  • Wayne from Leesburg, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
78 of 100 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Frig not cold at all,Freezer was all defrosted
Well the frist thing I did was get out the all the paper work and look under trouble shooting.This frig has a list of codes to try to help narrow down what parts might be bad.Well at frist it seemed it was a Defrost Thermastat?Well thanks to PartSelect it showed me right where it was and step by step how to remove and replace it.It took me over 2Hr's,after that I let the frig run all night and the next morning(yep warm frig)not the part I needed,well now Im mad,the local part store said you need a 3in1 jump starter easy to in stall at $50.Can'nt bring parts back no way weather thier opened or not.So get home and can'nt see how this jumper is going to wire up to my compresser?So on to the Web site to get some info,find out that this part gets a thumb's down,it puts out more volt's then needed and kills your compresser the reviews where very help full.So back to PartSelect to see more info,then I spoted the Overload/Relay and went to the back of my Frig and this part just plugs right into the compresser,I pulled it of with pliers and Bingo a burn spot melted right through the Overload/Relay.Ordered the right part the same as the old one.Put the part in and Bam,compresser fired right up.If I only did alittle more home work I could off saved alot of head ach and money.Thanks PartSelect I'll alway's click on to your web site for future parts and advise.
Parts Used:
Compressor Start Device and Capacitor
  • Denise from SOUTHINGTON, CT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
64 of 70 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the LSD2615HEW
1 - 15 of 898