LSC27910SW (ASW2LGA) LG Refrigerator - Instructions

After checking the prices of new refrigerators, I decided that I had nothing to lose trying to repair the sticking ice/water dispenser. I followed the previous instructions by prying off the panel with a screwdriver working my way around. Some effort is needed, but it will come loose before it breaks. You should remove the funnel first. I ... Read more f you have an older model, the funnels are fragile and should come out with a gentle back and forth jiggle. I broke mine. After pulling the face off the frig,I noticed that the plastic piece the activates the dispenser was partially out of its cradle in the rubber piece. Apparently pushing too hard on it can dislodge this piece and cause the unit to stick. Check this out before going for a new actuator. It only took a few minutes to clean and reassemble and reinstall. Works perfectly. Received new funnel and it was different than the one I took out. I missed the note that said if you order the funnel, you should also get the bracket to be sure they go back together. Two lessons learned. Don,t be afraid of this repair and don't push too hard on the dispenser.

To replace the warped tray, I found the service manual (pg. 124 below) which took some interpreting.
Removed the lever. Then removed the assembly by two screws that are forward to the unit and go upwards.
The insulation, sensor, and sensor cover are simply pulled down and off and the unit separated to removed the tray, and ... Read more then insert the new tray. Proceed in reverse. Takes only a few minutes.

/Users/grf/Desktop/fridge ice tray.pdf

The replacement gasket does not have as strong a magnet as the original one. I removed the old one carefully so as not to cause more damage in case I have to put it back. Using Tongue suppressor I pushed new gasket into place and put a thin coating of protelem jelly on the gasket. I just have to make sure the door is closed each time to ... Read more be sure of good seal.

This site was awesome! I was able to very quickly look up my refrigerator model, find the proper part number, and order the part. The only suggestion I would make is to update the cut sheet with a more clear version, it was a little difficult to make out the part number because the scan/drawing was fuzzy, but I was still able to make it ... Read more out. Got the part in the mail very quickly and it was super easy to remove the old rail and install the new one. Take out the screws from the old one, remove the old rail, line up the holes, install the new one, and put back the screws. It's so nice to have a site like this to fine parts and order them! Too cool! Thank you so much!

Very easy to replace right and left rail 3 screws on each side

I removed the lower back panel. The difficulty and time consuming part was finding the old parts. They were inside a cover on the side of the motor. The cover was difficult to remove. It slides away from the motor. The terminals on the replacement parts were oriented differently from the original, Like a mirror image. Accordingly, ... Read more I reversed the wires (side to side) and connected them to the replacement parts. The refrigerator is now working fine.

I paid for the expedited shipping and they sent me a cheap knockoff attempt at the part that had the wrong size hole. So they refunded me the money I paid for the part but not the shipping, and then I crushed the part they sent me with a hammer and threw it away.

First ,I unplug the refrigerator .
2nd i remove the back cover, clean the dust.
3th disconnect the water line, remove the all valve..
4th unplug all the wires and code ea with a No,remove the water lines
5th replace the valve reconnect the wires and water lines.replace the
back cover at last screw back the w ... Read more ater line.check for water leaks .
i found ease the valve replacement installation.
.Thanks for the video.

Really Easy

Replaced water pump assembly, all compression fittings easy to put together

It was a "snap to complete it" inasmuch as the part just snapped in.

I am a woman and I did this in about 10 mins. I turned off the water, disconnected the water line, took the back off the fridge, disconnected the motor plug and unscrewed the fan. It took a little maneuvering to get the fan out but once I did it was a breeze. Opened up back door that housed the motor, took the motor out and put in the new ... Read more one. Put everything back together and it's working great. Very fast shipping so don't pay for the expedited way to ship. I ordered Sunday night and it was in my door by 10:00 Tuesday morning.

Just replaced the old shelves with new

replaced gaskets for the second time in four years

Simply removed the drawer, then removed the shelf above which held the guides, removed the guides ( 3 screws per side )and replaced them.