This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as ...Read morethey commonly wear at the same rate. This is about 1 inch long and metallic in color.
This is an authentic OEM part sourced directly from the manufacturer. The crisper slide rail for your refrigerator allows the crisper drawer to slide in and out, and supports the drawer as it does so. This part is for the right side of your crisper drawer. Please note that the roller for this guide rail is a separate part under part number PS11759956.
This part is the replacement ice tray for your refrigerator. The tray is made of white plastic and is approximately 9 inches in length, and 3 inches in width. It has the capacity for 8 ice cubes. The ice tray can be filled up with water and is the mold that shapes the ice cubes. If your current ice tray is cracked, warped, or if mineral d...Read moreeposits have settled inside it, it may cause the ice cubes to stick. This part is sold individually and is an authentic OEM part.
This genuine OEM lever spring exerts tension between the ice maker door plunger and the ice maker itself on your refrigerator. If there is little to no tension holding your ice door seal in place, the spring may be faulty. This spring is approximately 1-inch long. Remember to disconnect the power to your refrigerator before beginning this repair.
This condenser cooling fan motor is an essential component for maintaining your refrigerator’s performance. It circulates air over the condenser coils located at the back of the unit, helping to dissipate heat and regulate internal temperatures. Proper airflow prevents overheating and ensures efficient cooling. If your refrigerator is run...Read morening too warm or too cold, making unusual noises, or failing to start, the fan motor may need replacement. Installation typically involves disconnecting power, removing the rear access panel, and securing the new motor in place. Designed for durability, this part plays a critical role in keeping your appliance operating smoothly.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sticking Ice dispenser
30 of 50 peoplefound this instruction helpful.
James from Englewood, FL
Easy
15 - 30 mins
Screw drivers
After checking the prices of new refrigerators, I decided that I had nothing to lose trying to repair the sticking ice/water dispenser. I followed the previous instructions by prying off the panel with a screwdriver working my way around. Some effort is needed, but it will come loose before it breaks. You should remove the funnel first. I
... Read moref you have an older model, the funnels are fragile and should come out with a gentle back and forth jiggle. I broke mine. After pulling the face off the frig,I noticed that the plastic piece the activates the dispenser was partially out of its cradle in the rubber piece. Apparently pushing too hard on it can dislodge this piece and cause the unit to stick. Check this out before going for a new actuator. It only took a few minutes to clean and reassemble and reinstall. Works perfectly. Received new funnel and it was different than the one I took out. I missed the note that said if you order the funnel, you should also get the bracket to be sure they go back together. Two lessons learned. Don,t be afraid of this repair and don't push too hard on the dispenser.
Read less
Was this helpful?
Thank you for voting!
The ice tray had warped and dumped water, which then froze down through the ice bucket and below.
8 of 8 peoplefound this instruction helpful.
George from ATLANTA, GA
Easy
Less than 15 mins
Screw drivers
To replace the warped tray, I found the service manual (pg. 124 below) which took some interpreting. Removed the lever. Then removed the assembly by two screws that are forward to the unit and go upwards. The insulation, sensor, and sensor cover are simply pulled down and off and the unit separated to removed the tray, and
... Read morethen insert the new tray. Proceed in reverse. Takes only a few minutes.
/Users/grf/Desktop/fridge ice tray.pdf
Read less
Was this helpful?
Thank you for voting!
Replace Gasket on refrigerator door
6 of 10 peoplefound this instruction helpful.
Curtis from DEMOPOLIS, AL
A Bit Difficult
30 - 60 mins
Screw drivers
The replacement gasket does not have as strong a magnet as the original one. I removed the old one carefully so as not to cause more damage in case I have to put it back. Using Tongue suppressor I pushed new gasket into place and put a thin coating of protelem jelly on the gasket. I just have to make sure the door is closed each time to
... Read morebe sure of good seal.