LRSC26925W LG Refrigerator - Instructions

To replace the warped tray, I found the service manual (pg. 124 below) which took some interpreting.
Removed the lever. Then removed the assembly by two screws that are forward to the unit and go upwards.
The insulation, sensor, and sensor cover are simply pulled down and off and the unit separated to removed the tray, and ... Read more then insert the new tray. Proceed in reverse. Takes only a few minutes.

/Users/grf/Desktop/fridge ice tray.pdf

I replaced solenoid, flapper heated door, and broken spring. Very easy instructions on "YouTube"

Removed old rails and tapped new rails in place. The big problem was finding how to fix the drawer. After searching many online websites, It was my good fortune to find Partselect and a one of their service representatives who
knew how to fix my drawer
and they had the part.

1. Remove the filter - 1 screw at top of filter and pull-out. 2. Use crescent wrench to push down at tube inlet and pull tube out. 3. Remove bottom screen from refrigerator. 4. Use crescent wrench to push down on water inlet and pull out tube. 5. Route new line on back of refrigerator. 6. Install is the reverse of removal. Thanks.

First ,I unplug the refrigerator .
2nd i remove the back cover, clean the dust.
3th disconnect the water line, remove the all valve..
4th unplug all the wires and code ea with a No,remove the water lines
5th replace the valve reconnect the wires and water lines.replace the
back cover at last screw back the w ... Read more ater line.check for water leaks .
i found ease the valve replacement installation.
.Thanks for the video.

Remove two screws on top of the fridge; removed old switch and inserted new switch. Worked like a charm. Replace casing and screws.

Replaced water pump assembly, all compression fittings easy to put together

Water valve replacement at back bottom right. Removed, water supply line and old valve with 1 screw and removed clips from hoses. Replaced with new valve and re-clipped hoses. Easy fix! Cleaned coils and back with blower and vacuum cleaner while I was in there too. I also had leak in water supply line, replaced. Ice trap door replacement ... Read more was a little more challenging. Hard to get off the ice dispenser funnel (Part# 278D). Has 4 lock clips on it and 1 broke when I took it off. This part# 278D is not available from part select?? Tricky to replace the trap door itself. Have to make sure the door valve sits in solenoid correctly. Installed wrong the first time and door would not open/close. Had to go in and reset orrectly. Works like a charm now. Still need part# 278D!!

I screwed the old one out and replaced it with the new one. A no-brainer. The thing that was so amazing was that I ordered the filter on the intrnet and it arrived the very next day!!! I was very surprised and pleased with the very quick shipping!!!

purchased a new switch. The old switch just needed to be lightly pried out with a screw driver, then it was simple to unplug the old, and plug in the new. Voila! Light !

So easy that my 13 years old son replaced it.

The part was extremely easy to replace. The unit came out with one screw, and I had to unplug the wire connection. After removing I noticed the ice tray was cracked - that's what caused the problem. The new unit went in easily with 1 plug in connection and 1 screw. I was done in less than 10 minutes.

I took the ice out with one screw and took out the old tray the new one slipped right in and I hooked up the little heat strip with one snap works perfect cost $10 I was told by appliance repair tech that I needed to replace the ice maker for $450 saved $440 dollars replacing the bent or warped ice tray

With alot of elbow grease and a pair of pliars we managed to get the old connector off wo cuttig the tubing as the tubing was getting to short from being cut once to many times & there was no more play in the length.Original connector was a different color and shapped slightly different than the new one so was a bit concerned that I had ... Read more ordered the wrong part but it went one very easily & did not leak. We even managed to remove it again just to see if it was possible wo cutting again. it came off with no trouble.I would say the replacement part was a better fit than the original simply because we could remove it easily wo having to cut the tube!

Shut water valve off drained water in refrigerator instAlled new valve