LP25939 Murray Snow Blower - Parts

The Oil Seal is used to seal the gear case where the axle extends from the case, around the axle shaft. It's rated as "Easy" to install, and will require a wrench set and seal puller. When installing, use something big enough to make contact with the entire seal, such as a PVC pipe, and tap gently into place. If broken, you will see oil ...Read moreleaking, and the part must be replaced. This gray, rubber part is sold individually. Refer to your make, model and diagrams to ensure this is the correct part for you.

This genuine item is supplied by the original equipment manufacturer for use with Murray, Simplicity and Snapper lawn mowers. It is the special retaining ring for the wheel. If the hardware is missing or is damaged, this will provide an identical replacement for the original part that was installed on a new unit. One durable metal retaini...Read moreng ring is included. Make sure to check the appropriate diagrams for your model to ensure the correct repair procedure.

BOLT, 5/16-18 x 3/4" Short Neck Carriage, GR 5

This quarter-inch Nylock nut, or hex nut, is silver in color and sold individually. Made of metal, its simple task is to secure and lock parts in place on a variety of different equipment. Regardless of the specific function, this nut may become damaged over time and if you notice the part it is securing becoming loose, it is time to chan...Read morege the Nylock Nut. Use a wrench to make this repair, ensuring your torque to the manufacturer specs. Most of our customers found this to be an easy repair, but difficulty can vary depending on the part you are accessing to make the repair.

This 5/16 washer, or toothed washer, is sold individually. It provides a tight fit between the knob and the upper handle on a range of outdoor power equipment. It attaches between the wing knob and the upper handle, and over time and through use, can become damaged and need replacing. It is gold in color and metal, and repairing it is an easy task according to our customers.

This is a genuine replacement part sourced from the original manufacturer for use with snowthrowers and lawnmowers. The special capscrew is used with several different models of equipment, and the application of the capscrew can vary based on the model of snowthrower or lawnmower. This capscrew is available as an individual replacement part, please see model diagram for associative parts.

This centerlock nut, also known as a flange nut or hex nut flange is a manufacturer approved replacement part. It is 5/8 of an inch with 18 threads per inch. The nut is designed to secure the bolt or screw it is positioned on and prevent it from loosening during use. It has a series of ridges on the inside that allow it to grip the thread...Read mores of the bolt or screw and a flange at its base to provide a larger surface area to clamp on. Over time the lock nut may break or become stripped. Inspect all the centerlock nuts on your equipment as you may need to order more than one for your repair. To install a new nut, use your hands to thread it on and use a pair of pliers or a wrench to tighten it until it is securely held. Be careful not to overtighten the nut as this can deform the nut and wear down the threads that keep it secure. If you experience difficulties removing or tightening the nuts, use a centerlock nut tool or a cassette lockring tool instead. Note that this nut is sold individually.

This bolt is a genuine OEM replacement part used in a variety of lawn and garden equipment. It is 2 inches long with a head diameter of 5/16 inches, and a thread pitch of 16 threads per inch. The bolt is used to secure the upper and lower handles on your equipment. If the bolt is stripped or damaged, your handles will become loose and fal...Read morel out of alignment. You may also notice increased shaking when using your equipment. Replace the bolt promptly as the handles can eventually collapse. Each bolt sold individually.

Introducing our Snapper Motor Spout Rotator an essential component for snowblowers. This Electric Motor driven deflector chute motor contributes to directional control of the snow output. The purpose of this particular component is to drive the chute rotation gear for efficient snowblowing. The installation process requires wearing work g...Read moreloves to ensure your safety. Manufactured to function optimally this appliance offers your snowblower a reliable performance. Experience excellent maintenance with this premium quality part from Snapper.

This part is an OEM from Craftsman for use with Snow Blowers. The extension spring is used to provide tension between the link rods, and disconnect arm which slows the riding lawnmower down when the speed control is pushed. The most common reason for replacing the spring is if the drive belt does not have enough tension to engage the auge...Read morer pulley because the spring is broken. This part is sold individually. The tool that you will need to replace the extension spring is a socket wrench.

This bolt is designed for use with various models of lawn and garden equipment and is a genuine OEM part. Featuring a square securing-area underneath the head for locking purposes, this bolt measures .31-inches in diameter and is 18 threads-per-inch. This bolt is made of high-quality metal and may require you to acquire multiple, depending on the use and location of installation for your equipment.

Pinion-1.417od 0.296s