KUIO Ice Maker - Instructions

The real difficulty is removing the screws. Even with a nut driver the space available makes them difficult to remove. I went to the hardware store and replaced the screws with screwdriver slots for re-installation.

Instead of hiring a technician to repair my 2022 Kitchen Aid ice machine for parts, labor, & service call of $300+, I decided to research a little. Google & U-Tube directed me with what was most probable wrong & walked through exactly how to replace part needed. The secret or guarantee correct repair is to use OEM parts only. $59.50 later ... Read more with OEM part from this site/ Fixed and working as new again. Thanks .

(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fi ... Read more tting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!

Unplugged the unit. Removed 2 screws to remove front cover to access the cutter grid.removed 2 screws to the cutter grid, unsnapped power connector and removed broken grid. Slid new grid in place, reconnected power connector, replaced screws, plugged in ice maker and slid back in place. Very easy!!!

Followed the instructions in the video provided via email from Partselect
However, the part received was the opposite design of the part removed.
It appeared this could be left hand right hand choice of part. Moreover, the button on the switch that turns the light off/on when door is open/closed was not functional due to the ... Read more part being the opposite of the part I was replacing. I tested the switch I was replacing and it appears this is not the problem. I think the light socket is the problem. I am 69 year old female and capable of doing small repairs, but limited knowledge of electrical so having to troubleshoot by trial and error. Thank you.

Pull the white cover from the front of the machine. Remove the screw that holds the thermistor body in place. Disconnect the old thermistor. Plug in the new thermistor. Snap the new thermistor body into the cover and reinsert the screw to the sidewall. Replace white cover. Complete!

Just install the new valve by reversing the process of removing the old valve. Only possible nance is with the quick release hose fittings - the collar is pushed down to release the hose. Also, be sure to FULLY reinsert the hose in the new valve. Best to twist the hose a bit when inserting so it goes through the o-ring inside the valv ... Read more e. If not fully inserted, it will leak.

Followed YouTube instructions. Went flawlessly!

This is the second time for this repair. Seems to occur after cleaning. Make sure you get the right part. Look at the old thermistor for correct model number, they look the same but are different. Turn off machine, unsnap cover plate, unplug old thermistor, remove holding screw with nut driver, replace in reverse order, turn on ice machin ... Read more e. Next time I clean the machine I may remove the thermistor.

Removed broke wire and replaced new wire. Use gloves to pull the wire tight. That's very important.

I thought the water bucket wasn't holding water because the icemaker continually was running - however, the crack didn't go through. The real issue was the Thermostat.

You've got to be able to sit or kneel and fit both arms in the unit for a while, so if you've got patience and ability, you can do it. If you have a battery op ... Read more erated screw driver with a nut and 6 star nut remover, this goes quicker.
Do not throw your old plug away, it doesn't come with a new one.

The hard part was getting the black thing (that attaches to the icebucket) back on. I had to go to Lowes and get a gasket and silicone grease to replace the one on it. I thought this was the reason it wouldn't go back on, because the gasket wouldn't fully fit back into the white hole.
I measured the diameter of that hole compared to the old one. It was slightly smaller and was not as smooth as my old one (it had manufacturing form lines and excess plastic that hadn't been removed)
I Dremeled it to increase the diameter, especially where the gasket was buckling out when trying to fit it on.
I finally got the black part back on.

I found later that it was cheaper somewhere else, however shipping charges are less and most parts are next day delivery.
I just ordered the thermostat. Wish me luck!

I was anticipating that the fan would be facing the back of the refrigerator. It actually was perpendicular to the back. There was some difficulty removing the bolts of the fan. I persevered and was victorious.

I popped out the old switch with a screwdriver pressing down the tab on the bottom and unplugged the terminals. Then I plugged in the new switch and popped back into the socket. Piece of cake!

I replaced the two pumps, since both were the same design...figuring if one went bad then the other would soon go bad...and then I also replace the water level sensor. All had quick connect plugs. The time is just taking apart the various pieces, cleaning, installing the new pumps and sensor, then reassembling.

Figured out You have to pop off the cocer than remove the 1/4 hex head screws only not the philips ones