KUDR2 KitchenAid - Instructions

all I had to do was snap the plastic piece in.
thanks, great experience.

We were told by a repair guy to buy a new dishwasher-about a $900+ cost to replace. Then a local parts place and Sears each quoted us $85 for the part plus $129 to come out. Found your website and bought the part for $17. Also bought a hard rubber gasket that fits on the bottom of the door for $8. The brackets that came with that last par ... Read more t were the hardest to install, but the gaskets took 15 minutes. We did glue another strip of the long door gasket along the area under the door lip. Works great! Saved over $800. You rock!

Grabbed old seal and removed it.(notice how seal was situated in slot)

Pushed new seal in slot that held old seal. close door.

If dishwasher still leaks you put the seal in backward (I did!)remove seal reverse it and reinsert it.

I read the instuctions and snapped it together just following the pictures...reading only when the picture was not enough information for me. My husband thought I pulled it out of the box already put togethr, he did not know I put it together.

Replaced the lower washer arm retaining nut,bearing ring.and seal in about 3 min.The retaining nut had broken off inside - make sure to remove the broken piece-I used needle nose pliers.
The dispenser took about 35 mins. Removed all the screws around the inside of the door and removed panel.Removed screws holding the dispenser and re ... Read more placed.I took time to give the dishwasher a good cleaning(inside edge).
Now my wife is happy.

Installed the new upper spray arm mount. First I installed it backwards which made the blades not turn freely (rub against top rack basket). Turned it around and was good to go. I found it helpful to remove the top basket in order to do this. Note that this clip is gray while your dishwasher tines are white. This does not cause any harm.

remove the lower arm and pieces.. get the parts stacked in the right order and hand screw the retainer nut... done! I decided to spend a little more and replace the whole washer arm and I'm glad I did. My dishes are coming out clear then they have in years!! Ordered the parts Thurs morning... thought i might get a load or two done ... Read more but when I opened the washer on friday it was obvious I was facing a weekend of teens having to handwash dishes! 15 minutes later the doorbell rang and there were the parts!! Woo Hoo!!

Plastic parts on this Kitchenaid dishwasher suffer repeat wear problems from heat and chemical detergents. The retainer nut on the bottom wash arm split horizontally int the thread area, and during operation, the wash arm would rise up and hit the bottom of the lower basket so there was a worn groove in the wing on top of the nut and the ... Read more dishes weren't getting very clean. Simple replacement, just screw the nut down. Also decided to replace the bearing ring right under the wash arm because it was getting pasted with white crust-like material from hard water and chemical detergent residues. I've dealt with PartSelect twice now, and they are fast and efficient. The online parts breakdowns are easy to follow.

First remove front panel of dishwasher. Held on by 2 screws on bottom of panel. Remove the electrical connections from the dispenser. Remove the six screws on the dispenser and remove dispenser. Reverse steps to install new dispenser. Also remove rinse aid sensor from old dispenser and install in the new dispenser.

Removed upper basket and installed the arm. New snap in didn't require phillips screwdriver as old one and new support had split to insert. Replacing upper spray spinner dropped screw down around pump. This caused misery unassembling lower covers to receive Stainless
Steel, so magnet won't help ended up with mirror and hemistat t ... Read more o reach through large screen figures. So make sure to put towel or something in the bottom to catch parts.

Removed inside cover and inserted new handle on two tabs and attached latch. Slightly tricky to get 3 pieces in place and reattach cover without them moving.

unscrewed sprayarm, removed bearing and seal, used PartSelect pic and description schematic to identify part numbers then placed order. Parts arrived in two or three days.

All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,

I first removed the old part. when i removed the old part i could not get the conector piece off when i when to get a new one they told me i should replace the copper tubing with the more flexable tubing because the copper tubing can kink up and possibly break from the kinking. so i screwed the inlet valve on i put teflon tape on the all ... Read more the threads of the conector piece screwed it into the new inlet valve with and adjustable wrench then i conected the new tubing, and tightend it down with the wrench i slowly turned the water back on to cheak for leaks. When i saw there were no leaks i turned the water on the rest of the way pushed the dishwasher back in and screwed it into place an i was done.

first I removed lower basket. then removed lower sprayer attached to pump housing by unscrewing the cap by hand. the I removed the pump cover . there were six alan screw two of them were missing causing the failure of the seal spraying solution at the door. replaced the pumpseal working backwards until everthing was replaced.