KUDR2 KitchenAid - Instructions

I turned off the circuit. I removed the interior side of the door and then the plastic covering over the electrical wires and switches (I counterbalanced the door with a couple of half gallon juice containers). I removed the wires attached to the switch on the door handle and the door handle itself. The handle and switch parts disassem ... Read more bled and I replaced the switches (part of kit). I cut off the singed wire and the other three beyond the damaged portion and stripped the wires and connected the extensions (part of kit). I attached the new wires to the switches and closed up the interior door. Lastly, I turned the circuit breaker back on. All was well!

Just followed the instructions and used the old one as template to snap components together. Quality seems to be same as the original one and Part Select was some 15% plus less expensive then next best competitor

The only difficult part was taking out (relatively easy) and returning (hard) the clips from the rails. This required bending the end of the metal rails with pliers. Otherwise the dishrack just rolled in with no issues.

The spinner is somewhat lower than the one it is replacing, making the clearance over items in the lower rack ... Read more to be serviceable but marginal.

Water was not being sprayed thru the arms. I opened the dishwasher, removed/unscrewed the spray arms and wash impeller (black plastic wheel that directs the water) and then noticed that the part below the wash impeller had broken into pieces. There was only a metal ring and it was supposed to have a spring attached to it. I replaced the r ... Read more ing/spring below the wash impeller using the part from the Drain and Wash impeller kit. The dishwasher works great now.

It was my first mechanical fix. Use the web to diagnose, find the specs of the appliance and use common sense and you can do it yourself too.

By the way, the parts from this site arrived the next day.

We couldn't find the model # on the web site and took a chance ordering the rinse cap for other models of that brand. When it arrived within a few days,it was simply a matter of pushing the new rinse cap into position. The replacement was of higher quality than the original. Although the price seemed a little high, it enabled me to use a ... Read more rinse again. We are very pleased.

Turned off the power, just to be safe.

Removed the lower panel (4 screws). That made it easier to remove the lower 2 screws on the door panel. Slid the panel down slightly, then pulled off.

Removed the old dispenser - disconnected 2 wires, removed 6 screws, pushed in the plastic clips.

Pushed the new unit ... Read more into place - clips click in. replaced 6 screws and 2 wires. Put the panels back on. Power on.

About 25 minutes.

Removed old seal, cleaned track, applied adhesive for new seal, seated new seal in track, closed door for 24 hours to allow adhesive to cure, then used dishwasher without difficulty. An easy repair.

Install was very easy. Used hands, pliers to pull out old gaskets. Wiped down old dirt in track. Started from (top) middle of door frame and used some soap with warm water to insert new gaskets. That's it! Kept old plastic brackets in place because it was too difficult to remove door springs. Old door seal and lower door seal were badly ... Read more worn (gummy and falling apart) - Thought that was the issue with the water leaking. Nope, I was wrong. Looks like the tub seal, and the plastic bearing that is under the spray arm. Going to buy new instead of diving in the money pit. 10 years old, motor corroded from water over the years.

Turned of water and unplugged the dishwasher.
Disconnected the incoming water line.
Drained on to the floor (have paper towels ready)
Disconnected the electrical feed wire.
Disconnected the rubber hose.
Unscrewed screw holding the fixture to the frame.
Took off the brass elbow from the old part.
Put pipe ... Read more dope around it and screwed into new part (carefully, so as to not crack plastic again).
Attached part back to frame.
Attached water lines.
Turned on water, plugged it in and ran dishwasher looking for leaks. No problem.

First turned off the power at the breaker box. I removed the screws on the inside of the dishwasher, then took off the front touch pad control panel. Removed the old fuse, tested it, orderd a new one. Left the DW dismantled while I waited for the new part. Then put it all back together. I have also replaced the latch on this same DW, ... Read more but they were both pretty easy.

Was able to replace and repair without taking the dishwasher out. Thermostat is behind and to the left of the power junction box. Has 2 wires going to it. It is up against the bottom of tub. I used an angled mirror to see what I was doing. 1 small screw to detach and pull down thermostat. Be sure power is off before you start. ... Read more Also reprogrammed defaults. Hit any button 1-2-3, 1-2-3, 1-2-3, fast and close door. Let it sit 15 min to run and re-set defaults. Now I have heat and dry dishes.

This part is different than the original but works great. I used Geronimo's instructions, but cut the ring (see below) so I didn't have to glue it back together.

1-remove upper rack by removing holding clips.

2-remove old assembly from Rack

3-Use exacto knife to cut old ring guide at top between 2 hooks t ... Read more o accommodate new style (one solid plastic piece). No need to re-glue since the hooks hold it up okay.

4-re-install upper rack

First of all, we were very impressed with the ease of finding the parts, the ordering, and the velocity in which the parts were shipped. We received them the next day. I had to remove one of the screws from the old kit, since the new one only came with one. I looked at the diagram on the website of the assembly, and also remembered what t ... Read more he assembly looked like before I took it apart. The first time I tried it, I could not get the spray arm to spin without hitting the dishwasher rack. Since I had ran out of time, I had to wait until the next day. Once I started, I realized that I had the mounting bracket on backwards. Once I turned it around, I tightened the screws, and it was done within 5 minutes.

AIR INLET GASKET Had to pull dishwaher out, using instructions sent with part, turn it 1/4 turn counter clockwise, tap with screwdriver and hammer and it came right off. Put the new one on. It was kinda hard to get it to turn the last little bit, I had to use a screw driver and hammer to make it twist that last little bit.

As others have said, installing this part is more difficult than it looks. First, it is a bit of a jigsaw puzzle. It is not intuitive which part should be attached first. I also found that part that clips onto the the bottom of the "rail" was just too tight. After a little surgery with an razor blade, I got it to fit. Also, there are ... Read more at least 3 different pivot clips for the upper rack. Pay attention to the diagram when ordering. (I didn't the first time, wrongly assuming that a pivot clip was a pivot clip.)