KUDD2 KitchenAid Dishwasher - Instructions

It was simple. I simply replaced the old water tube with the new one you sent, and it works like new. Piece of cake.

Removed old tube.

New tube was a little tight, so I heated it with a hair dryer and used dish washing detergent - Joy - as a lubricant. Then the tube slipped on easily.

Repair was fairly easy, had to swith the mounting bracket from the old valve no problem. Install reconnected the water and the dishwasher works great now!

Very easily!! I am 19 years old and repaired the dishwasher for my grandmother in about 15 minutes. Great products.

Pulled off old tube and upper arm receiver.The new tube and the section it was to go on appeared to be too small. I heated new tube with hair blower and streched new tube so as to fit .

Removed bottom rack and replaced axles and wheels, works just like new and did it without any assistance from my son or Husband.

Removed old water tube and replaced it with the new one. Hard part was logistically trying to put it below the rack and it obviously it had to fit very tight and it was quite difficult to get in place, but I did it! Thanks to your easy to use website and excellent service. I was proud of myself for doing the whole job start to finish, ... Read more and my husband was even more impressed. Only downside to that is that I think he'll be playing more golf, while I do the repair work from now on.

After checking for blockages in the drain line and finding none, I disassembled the wash wand assembly and discovered a gasket that had really deteriorated. Since there was nothing else apparently wrong, I took a chance and went shopping for the gasket. None of my local stores could provided me one so I searched on line and found it at ... Read more Partselect. It had to be special ordered and that took a while, but when it arrived, I put the new gasket in and had a perfect dishwasher again for less than 15 bucks. The schematic I was able to print from your website was invaluable.

removed the two cover in front of the dishwasher then removed the water inlet valve located behind these covers. replaced the old valve with a new valve by connecting the water supply line and the outlet hose going to the dishwasher.

I was trying to avoid having to buy a new dishwasher before the holidays. I went on YouTube and found the dirty dishes may mean bad water inlet valve. So, I used my meter to see if the valve was bad and sure enough it was. I ordered the part from Part Select. Once I received the part I removed the old one. Be sure to put a towel down to c ... Read more atch the excess water. The bracket that came with the new prt was a different configuration, but i swapped the new with old and it worked. I addition to the valve being bad the dishwasher upper and lower arms were somewhat clogged. I looked online again and followed YouTube instructions to clean. The dishwasher is cleaning like it is new. I would recommend to anyone doing work on their dishwasher to use part select and thoroughly clean the upper and lower arm.

pulled off the old and put on the new. Great pictures on website so I got the right part the first time. Thanks!

It was 94 degrees that day so I set the rubber hose outside in the sun to loosen it up, make it more plyable. I then mixed up some soapy water and doused the ends of the hose with the soapy water and slid the hose right onto the fittings.

There was a small hole in the hose which was not discussed in the directions. I assumed ... Read more the hole should be installed on the down side to let water drain out after the dishwasher is finished. This will reduce the chance of bacteria building in the hose.

I read the installation tips before I started and picked up the soap mix and heating up the hose before installation. Can be accomplished with a hair dryer if it is not 94+ degrees outside!!!

Thanks,

Jim

I removed the upper rack from the dishwasher by popping the two rack track stops out of the rack tracks. The old tube came off easily, and the new tube went on very nicely, after lubing each end with a dab of liquid dish soap. I put the rack back on its tracks , popped the track stops back in and my dishwasher was back in business.

I ran the tube under warm water and it was very easy to connect. I would have done it a lot sooner if I had known how easy it would be to find the part and install it.

I removed the roll out top wire rack of the dishwasher, turned it over and pulled the old punctured water supply tube off the force fit connectors on each end. I put a small amount of vaseline lubricant immediately inside the mouth of the new tube at each end. I pressed the ends of the new tube over the force fit connectors and tested th ... Read more em by shaking the pipe. I replaced the rack and fastened it into place.