KUDC22 KitchenAid Dishwasher - Instructions

I put a whirlpool tube on my Jen more dishwasher . Fits like a glove.

I took out the bottom rack, turned it upside down, popped off the wheels and saved them and put on the new axles. It took a little doing to get the new axles snapped into place-they were stiff. I finally figured out how to use the pliers at the right angle to pop them on. Then the wheels popped right on and off I went.

we used hot water to soften the ends of the tube and then slid it onto the two ends of the parts in the dishwasher. It did take a little bit of "push" to get it on one end, but nothing we could not handle. I would say anyone with common sense and willingness to fix something them selves would have no problem. I would like to say the pa ... Read more rt I ordered was of good quality and saved me a lot of money.

Like the video showed but very hard to stretch tube over wider part on interior of top shelf. Read afterwards that hair dryer would have helped. Video should mention that. Bruised hands and wrists getting it on good.

Closed water supply--Turned circuit breaker off to dishwasher--removed lower panel on dishwasher--removed the two wires from water inlet valve--disconnected water supply line--removed angle fitting from old valve & installed in new valve--reinstalled new valve & connected water line & 2 wires--This fixed problem.
I ordered part 11:0 ... Read more 0 1/15/09--Recd. new one 10:30 next morning. VERY FINE SERVICE & PRICE from PARTS SELECT.COM--Thanks.

Repair was awful without instructions. Instructions were requested twice with no response. Attempted without instruction and broke the sleeve. Reordered but not through Partselect

ReplacING the tube was not a big job but the old tube had come apart and pieces had lodged in the sprayer arm. I used a toothpick and nut pick to dislodge the pieces and restore full water flow.

First I had to buy a new tray. I tried to remove the wheels from the old tray but they wouldn't come off without breaking. I ordered new wheels and axels and they went on fine with the aid of a C-clamp. Then I tried to remove the old bumpers but they broke when I tried to remove them.
So, I ordered two new bumpers. When I did I saw t ... Read more hat another user had posted a note saying that the new bumpers slipped on well if heated in hot water first. So, I heated them in hot water and they slipped on easily and safely.

Our diskwasher is over 20 years old. The manufacture did not even list the model anymore. Googled - Kitchenaid parts old. Found your site and order the part on Sat. night. It arrived on Wed. Installed as follows that night.
After reading other reviews on how the job went and seeing that people had problems getting the tube to ... Read more slide on the outlets I decided to take the rack completely apart so as to have unrestricted access to the connections. Would be easier to work the tube on to them.

First I removed the top rack by releasing the two retainers on the upper rack side rails which hold it up. Then I turned it with bottom up and released all of the plastic clips that held the bottom half of the rack in place. If a clip breaks you can use a nylon cable tie to replace it. Then I took out the screw that holds the metal water bar in place and removed it. Then I took out the screw that holds the plastic part that the water bar was mounted on off. Then with the outlet where the tube was to be mounted not connected to anything it was easy to slide the tube on it. I then was able to slide the tube on to the bracket at the back of the rack. Had to use a screw driver to help get the tube over the round outlet. Then worked it on to where it should be. Reassembled the top rack and put it back on the side rails and washed a load. It worked just like it did when it was new. Saved a service call $75.00 and only took about 30 minutes working at a slow pace.
Love it when everything works like it should.

I removed the rubber water tube before ordering the part. After receiving the part it took less than 2 minutes to replace the part. Now the dishes are clean!!

I removed the old hose, I lightly coated the id of the new tube with vasoline, both ends, and then heated the oblong end with the hair dryer to soften it and it slid on with litte force. The round end installed without heating.

Removed the old axles and rollers and snapped in the new ones. Really easy repair.

So easy I could do it! I pulled the old tube off (after having dirty dishes for weeks and not realizing it was because of a hole in the hose. When I told my husband I was going to call a repairman, he suggesting ordering the part on line and doing it ourselves - no reason not to! Piece of cake!

Just popped the receiver onto the end of the pipe! I am so glad partselect.com had the part and made my job in finding the part I needed so easy!

Took off old hose. It practically fell off.
Used a spoon to widen the ends of new hose and twisted on one end, then other end slipped on. Done!