KSSP48MFS05 KitchenAid Refrigerator - Instructions

Unplugged refrigerator and turned off water supply. Loosened two top screws and removed bottom screw. Althought kit was supplied with multyple wiring harnesses the harness attached to unit was the correct harness for the model I was replacing. Removed and reused old shut off arm as replacement arms were shorter in reach then original. ... Read more Also reused bottom unit support that was removed and replaced with one screw into unit and then into side wall of freezer. Over all time less then 15 minutes. As this was a side by side ref/freezer unit their us limited space to view support screws. I used a mechanics mirror to find upper screws. This visualization made the process go much faster. Reading the other repair stories also gave me a huge confidence boost and insite in what to expect.

After first unplugging the refrigerator from it's electrical power source,I removed the lower screw of the ice making unit with a nut driver. I then loosened the upper two screws which hold the retainer clips that secure the unit tight to the freezer wall. I then lifted the unit upward and outward a few inches to allow access to the wire ... Read more harness. I unplugged the haness from rear of the freezer and removed the unit completely.
To install just reverse the procedure.

Loosened two top screws using a hand held mirror and screwdriver and removed a bottom screw then unplugged the unit inside. Five minutes and repair was complete. Easy as that!

Broken plastic part in motor assembly. Very simple to replace. Sears wanted $322.00!!!

I just followed the instructions that came with the unit, it was very easy. The old ice maker was taken out some time ago, so all I had to do was install the new one. It was three screws and one electrical plug. I removed the ice maker over a year ago and did not replace it at the time. I purchaced new handles also and they were easy to r ... Read more eplace. I then decided to try the ice maker, I got tired of buying ice at the store. The order came in just two days right to my front door. It was a very easy fix and now I have a refrigerator full of ice. Thanks for the great service.

It actually took me longer to think about the repair than actually doing it. It was three screws, two upper that you just loosen and then one on the bottom that you remove. Pulled the unit out and disconnected the power. Slipped the new unit onto the two upper brackets, after connecting the power cord, tightened the bracket screws, reatta ... Read more ched the bottom set screw and I was making ice. Incredibly easy. When I ordered the replacement unit they said it would arrive in 3-5 days, but it only took a day and a half. Great experience all the way through. I'm a customer for life.

removed the three screws holding the old ice maker in place - unpluged the electronics .... took the new ice maker pluged in the electronics screwed in into place and we were in business and had ice within an hour.

Used a nutdriver and removed the lower mount nut, then loosened the the top two nuts and the icemaker lifted off, then unplugged the device and replugged it into the "old" plug(the new ones were not needed) then remounted it. Then it did not fill (as others posted happened right away.) Some poster suggested manually filling the tray so I ... Read more did it. Later it froze and emptied and refilled and started working normally. Not sure if putting water had anything to do with it or it just took some time. It would be nice if the instructions addressed this issue.

First I removed the (3) screws holding the unit to the side of freezer wall with a nutdriver. Then I disconnect the Harness from the back of the freezer. You have to work the Harness off connector because it was very tight. The Unit came with the correct harness installed so I reconnected the harness to the Freezer and replaced the (3) sc ... Read more rews. I had ice in about 2.5 hours.

i followed the online instructions on how to take the icemaker apart, which were very easy to follow. Once the new part arrived it plugged right in and a few steps later it was back together. within the hour we were hearing the sound of ice dropping into the tray. thanks for all the help this definitely saved us money and hopefully we ... Read more get many more years out of this icemaker.

First, removed drawer and shelf with flip up lid. Second, removed 4 screws holding track in place and replaced with new part. Reinstalled shelf, flip up lid, and drawer. Easy fix with proper replacement part.

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Removed the one screw holding the unit in place in the freezer and pulled it out. Removed the 3 screws that hold the motor in place on the ice maker. Replaced the motor unit, replaced the 3 screws, and re-installed the ice maker.
Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here ... Read more for $65.

The repair was very easy. I ordered the part from Part Seelect and the delivery was very quick.
Opened the box and took out the new ice maker. Emptied the freezer, turned off the power and the water to the Refigerator / Freezer / Iceww Maker. Used a quarter inch nut driver to remove the old ice make. Really easy remove one scre ... Read more w and lewsen two ther screws. unplugged the wiring harness. Took the bale arm off old unit and installed it on the new unit. Check to make sure I had the right wiring harness installed on the ic make which it was. Installed and leveled the new unit. in a little over a hour I had ice. Had to make a few adjustments to the water level setting to make sure all ice cube trays filled up completely.

So easy to do a cave man could do it.

Wathced video (VERY helpful)of how to do repair to make sure it was within my capabilities to do. Made sure I had all requested numbers before ordering. Replacement part was an EXACT fit. 15 minutes of work and I saved nearly $150 of estimate by local service company. I am (and will continue to be) a repeat customer. Thanks. Mel