EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

KSSC36QTS10 KitchenAid Refrigerator - Instructions

All Instructions for the KSSC36QTS10
121 - 135 of 299

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice Maker Motor Broke (Plastic Cogs)
1 of 2 people found this instruction helpful.
  • Robert from Austin, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
1) Turn off the power to the refrigerator 2) Remove the top shelf and ice maker door 3)Remove three hex screws holding the ice maker in place, 4) Unplug the electrical cables and remove the ice maker 5) Remove the plastic cover to the motor module 6) Remove three screws from the motor module and seperate from the housing 7) Remove tw o mounting screws for the motor module 8) Seperate the motor module from the ice tray 9) Remove and replace the plastic ice stripper and rake10) Reassemble in reverse order. Note: Be patient after re-installing the ice maker. It might take an hour or two before its cold enough to kick back on and make ice.
Was this helpful?
Thank you for voting!
ice maker quit making ice
1 of 2 people found this instruction helpful.
  • Dale from Mansfield, OH
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench set
I replaced the Electronic control boards because the indicator lights were letting me know that there was a problem, but!!!! when that did not fix the problem, I took the ice maker out and removed the control module from the end of the icemaker only to find out that water had gotten in there and corroded the electronic contacts... this ma y have been why the indicator lights were not working on the emitter and receiver. I was going to purchase just the module, but the entire ice tray was beginning to de-laminate and plastic was flaking off all over. To make a long story somewhat shorter, I purchased a new icemaker and it works fine... one caution though... My icemaker did not come with any information that told me I had to flip the icemaker to the "on" position from vacation mode by inserting a screwdriver in the back of the module inside of a small white ring. This hole is where the shut off arm WOULD go if my model had one.
Was this helpful?
Thank you for voting!
light did not work on the refrigerator side
1 of 2 people found this instruction helpful.
  • David from GROVESPRING, MO
  • Easy
  • Less than 15 mins
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what i s inside the refer!
Was this helpful?
Thank you for voting!
Light switch broke off
1 of 2 people found this instruction helpful.
  • Kathy from TEMECULA, CA
  • Very Easy
  • Less than 15 mins
  • Pliers
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
Was this helpful?
Thank you for voting!
Rocker on switch broke off
1 of 2 people found this instruction helpful.
  • David Barnes from ROSWELL, NM
  • Very Easy
  • Less than 15 mins
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
Was this helpful?
Thank you for voting!
Filter replacement
1 of 2 people found this instruction helpful.
  • Thomas from BOTHELL, WA
  • Very Easy
  • Less than 15 mins
Easily removed old filter and inserted the new one
Was this helpful?
Thank you for voting!
Ice was made intermittently, and then no ice at all!
1 of 2 people found this instruction helpful.
  • Adam from West Valley City, UT
  • Really Easy
  • Less than 15 mins
  • Screw drivers
My ice maker about six months ago started to ice make very intermittently and eventually stopped all together. The emiitter no matter what I did was giving me two flashes then a pause, over and over again. I purchased the emitter kit and with a Phillips screwdriver in about five minutes my ice maker kicked the sulinoid on and ice was alre ady started!!! Fast and easy repair!!!
Was this helpful?
Thank you for voting!
dirty filter
1 of 3 people found this instruction helpful.
  • Sherman from DSRT HOT SPGS, CA
  • Very Easy
  • Less than 15 mins
pulled oil filter out put new one in maybe 10 minutes
Was this helpful?
Thank you for voting!
Ice maker not refilling
1 of 3 people found this instruction helpful.
  • Kenneth from Scott, LA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
1) unplug the refrigerator
2) remove the cover plate for the sensor board on your left facing the refrigerator
3) unplug the sensor board then remove the board from the cover plate.
4) install the new board onto the cover plate and
reinstall the board in to left side of the freezer compartment.
5) repeat this proc es for the right side of the freezer compartment.
The two boards are very different and you will have no problem telling the difference between them.
6)Plug the refigerator back in and observe the red indicator light on the right hand side of the freezer compartment (it should be blinking) . Then hold down the flap on the left hand side and the blinking red light should go solid on. If it hasn't you have another problem with the ice maker.
Was this helpful?
Thank you for voting!
icemaker not working
1 of 3 people found this instruction helpful.
  • j from mc gaheysville, VA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver
Did not have elec. schematics or instructions, thought the problem may be the emitter/receiver. Ordered these parts, and included in the package were instructions for testing the e/m bd. Followed instructions for testing the e/m and determined the e/m was OK. Did not remove the boards from the box. Checked the internet and found schema tic for the ice maker, tested and determined the ice maker was faulty. Problem solved.
Was this helpful?
Thank you for voting!
ice make just stopped making ice
1 of 3 people found this instruction helpful.
  • Ryan from Midlothian, VA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
i first removed the ice maker and took the motor assembley off. Right away i saw the problem. The wheel which drives the arm broke.
Once i get the new motor modl i just replaced it (it just pops into place with 1 or 2 screws).
put ice maker back in freezer and wola. Starting cranking out ice within 15 minutes.
Was this helpful?
Thank you for voting!
Ice Maker Stopped Working
1 of 3 people found this instruction helpful.
  • Joe from Omaha, NE
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Tough part was diagnosing the problem: bad water inlet solenoid, frozen inlet line, bad ice maker motor, or door opening sensor? Went to a parts shop & discussed the problem with the serviceman. He said you just need to sequentially replace each part. No way say I, that could cost $300 with a no-part return option.

I decided to replace the motor...Eureka!! It worked.
The underside of the ice maker cartridge has a plastic snap clip on either side of the cartridge. You need push each up, pull the left side of the cartridge out part way & disconnect the electrical connector on the right side(left..you facing the refrig.) With the cartridge out simply remove the 5 screws from the motor plate of the left side & replace with the new one.
Very simple. Slide the cartridge back in the frig. until the 2 snap clips click. Voila...you done! Cost $86..not $300. Apparently the motor is too weak to do the job & burns out quickly. Manufacturer should correct this defect.
Was this helpful?
Thank you for voting!
light staying on
0 of 1 people found this instruction helpful.
  • Cecelia from Beaver Dam, WI
  • Easy
  • 15 - 30 mins
  • Screw drivers
A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.
Was this helpful?
Thank you for voting!
ice maker wouldn't stop making Ice then quit 1.5 days later
0 of 1 people found this instruction helpful.
  • Juan from Tomball, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
removed 3 screws on each side of freezer where the ice maker controls are unplugged the circuit boards. un screwed the boards from the plastic and put the new ones in, reinstalled. now, Ice and not over flowing! :)
Was this helpful?
Thank you for voting!
Ice Maker Stopped Working
0 of 1 people found this instruction helpful.
  • David from Davis, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
After calling Sears and setting up an appointment and waiting 7 hours for them not to show.. without any phone call..even after the dispatcher said I was "Next on the List" I figured thilure was the Emitter boards.. I ordered theere had to be a better way.. I researched this site and determined that the most likely cause of fa parts and r eceived them within 3 days with standard shipping. I followed the optical diagnostic instructions that were included and replaced the boards. Within a few hours the ice maker was singing again.
Was this helpful?
Thank you for voting!
All Instructions for the KSSC36QTS10
121 - 135 of 299