This EveryDrop Filter3 is certified to reduce the most contaminants with Triple Filtration Technology. Now, you and your family can enjoy the enriching benefits of cleaner, freshly filtered ice & water. Not just in beverages, but for preparing meals, too. This advanced generation of ice and water refrigerator filters from EveryDrop Filter...Read mores are certified to reduce more contaminants with Triple Filtration Technology. Filter 5 reduces 16 contaminants, so you can feel reassured that you and your family are getting the most out of your water. Remember to replace your refrigerator filter every 6 months to maximize contaminant reduction.
If your refrigerators interior light is not working, the door switch may be the cause. It turns the light off when the door closes. This is an OEM part. Confirm compatibility using your refrigerators model number.
This appliance light bulb illuminates the interior compartment so stored items are easier to see and reach. Its clear glass design allows light to spread through the surrounding area, while the incandescent filament produces light when powered. A burned-out filament or damaged bulb may leave the compartment dark. Replacing a failed bulb h...Read moreelps restore interior lighting. Disconnect appliance power and allow the old bulb to cool before removal, then gently screw the replacement into the socket without overtightening and reinstall the protective cover. This is an OEM part sourced directly from the manufacturer.
When an ice maker is not making ice, its OEM ice level control board kit may be the part to check. The kits emitter and receiver use an infrared beam to sense the ice level in the bucket and signal the ice maker to make more.
A warm refrigerator or noisy evaporator fan can indicate a problem with the fan blade. This white, four-blade OEM part circulates cold air over the refrigerators evaporator coils. Confirm fit using your refrigerators model number.
This refrigerator ice dispenser drive shaft seal forms a barrier around the shaft beneath the ice bucket. It helps keep moisture and condensation from reaching the auger motor and inner door area. A torn, brittle, or worn seal may allow water to pass through, leading to leaks, rust, or moisture buildup near the dispenser mechanism. Replac...Read moreing a damaged seal helps protect the motor area and restore the barrier around the shaft. Unplug the refrigerator before accessing the drive assembly or removing the shaft. This is an OEM part sourced directly from the manufacturer.
This refrigerator ice level emitter flipper cover helps control the light beam used to monitor the ice supply. The white plastic flap pivots on a spring-loaded hinge beside the ice bucket. Cracks, broken hinge points, or a sticking flap may interfere with the beam and interrupt ice production. Replacing a damaged cover helps restore prope...Read morer flap movement and ice level sensing. Unplug the refrigerator before accessing the assembly, and handle the hinge pin, retaining clip, and spring carefully during replacement. This is an OEM part sourced directly from the manufacturer.
The ice maker thermostat, also known as the cycling thermostat, controls and regulates the ice maker ejection cycle by monitoring the temperature inside the freezer to determine when to release the ice into the bin and start the ice making cycle again. If your ice maker is making unusual noises, or if the ice maker is not making or dispen...Read moresing ice, there could be an issue with the thermostat. Before you begin this repair, make sure the power is disconnected from your refrigerator, and that any food that may spoil is safely stored. This is an OEM part and is sourced directly from the manufacturer. This thermostat is sold individually, and comes with two attachment clips.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
there were directions
754 of 1282 peoplefound this instruction helpful.
Kate from Jacksonville, FL
Very Difficult
30 - 60 mins
We didn't know where the product went and it was very difficult to install.
Was this helpful?
Thank you for voting!
six months the light turns red. time to replace filter
310 of 392 peoplefound this instruction helpful.
Leroy from Perkiomenville, PA
Really Easy
Less than 15 mins
First I shut the water off to the refrigerator.then i pushed the big button in the middle of the grille below the refrigerator door. pulled out the old filter, took the front cap off the old filter put it on the new filter. took the two red caps off the new filter. pushed the filter in till it locked in place. all done! Turned the back on
... Read more.
Read less
Was this helpful?
Thank you for voting!
Ice Maker would not stop making ice.
194 of 222 peoplefound this instruction helpful.
Vince from El Cajon, CA
Really Easy
Less than 15 mins
Screw drivers
First, I tested the ice maker "switch" that actually just covers the beam that regulates the ice maker. In the "off" position, it still made ice. Then, I removed the three screws on the cover over the transmitter and disconnected the circuit board at the wire connector. It stopped. After ordering and receiving the new transmitter and rece
... Read moreiver boards, I replaced both boards. They are located on either side of the freezer compartment under panels held in place by three screws. Probably saved 150 to 200 bucks.