KSSC36QTS10 KitchenAid Refrigerator - Instructions

After lots of internet exploring and diagnosis, the icemaker comes right out, and with three screws out and in, the job is all but done. Don't pay anyone for this repair!!!!!

Being too lazy to pull out the refrigerator out and unplug it, I turned it off at the fuse box. Opened the freezer door and unscrewed the three screws holding the sensor. Pulled the sensor out and unscrewed the board then unpluged it and removed it. Plugged in new board, screwed it in then replaced the three screws. Repeat on the oth ... Read more er side. The most difficult part was getting to one of three screws on each side; it almost required a third hand to hold the flap door between the ice maker and the bin, while removing said screw. I must at say that this product is definitely over engineered.

I removed the cap from the filter pushed a lever and removed fliter. I replaced the old filter, removed the caps on the new one and slid it into channel after replacing the outer cap. I removed water from the spigot for 4 mins. and it was ready to go. I pushed the reset button to get the green light to come on.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

Just put the new one in.

I found an EXCELLENT video (see link below) that shows with great detail how to change out several parts in the water/ice dispenser area on the freezer door for KitchenAid or Whirlpool brand, side by side units. This made my repair so easy!

https://www.youtube.com/watch?v=yK8ZnbQQ8qU

change light bulbs

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

Local service person missed the diagnosis and advised $10,000 new refrigerator. I looked and saw that the switch was deformed and had burn marks. Searched for switch online. Found site Ordered. Part arrived next day. 5 minute job to replace. No tools needed. Refrigerator works great. Thank you t!

Built-in filter was corroded due to age. New filter corrected problem.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

The troubleshooting time takes about 20 to 30 minutes. After checking out the solenoid (valve water), the water line, and the electronic board (emitter/receiver) are working fine. The only thing left is the ice module. I called Partselect and talked to a sale rep to make sure I get the right part, and the lady was so helpful by sendind th ... Read more e picture of the part so I can review before ordering it. I received the part in 3 days ( normal shipping) and did the folowings:
1) Unplugged the power cord from refrigerator.
2) Removed the ice module by removed a 1/4" screw from under the right side of the icemaker that retains the icemaker and a “U” plastic clamp and then pull out the whole unit it from the track.
3) Unplugged the cable connected to the ice maker.
4) Using the phillips screw driver to remove the 3 screws. Carefully pulled out the ice module and installed the new ice module.
5) Put the ice maker back to the freezer, plug the cable back to the ice maker and put the clamp and tighten the nut.
6) Plugged the power cable back to the wall.

The first ice I got in an hour and a full bucket of ice in less than 24 hours. I spent less than $80 for the whole thing. Thank you so much Partselect for the great service and the stories posted, it really helped me to get it done.

Removed screws, unplugged connectors to the two faulty circuit boards, reconnected both cables to new/replacement circuit boards, reinstalled screws. Extrremely simple! Worked perfectly! Saved about $150 in less than 30 minutes. Great, fast service by PartsSelect.

I called a local appliance repair / sales store and he told me what to look for. There is an electronic "eye" on the "On / Off" panel in the freezer, and there is an electronic eye that sends a beam across to the other side where there is a receiver. If there is no beam, or the beam is obstructed --- for example when the freezer door is o ... Read more pen the little "door" on the opposite side of the On / Off switch opens, interrupting the beam --- the icemaker will not work. In my case it was easy... there was no beam being sent across, so I KNEW it was bad.

Ordered the part, took out 6 screws total to remove the sender and receiver, removed the circuit boards with 3 more screws, replaced with new boards, and reinstalled.

Trust me - a 10 year old could do this. Don't be afraid because it involves "circuit boards" - it's literally one or two screws, replace the boards, screw them back in, and plug the two sides back in. ANYONE can do it... anyone!!!

Easy!!!!! Just cut the power to the unit and unscrew the boards. One is to the right of the ice maker and one is to the left. Snap the connecter on the old board so it will disconnect and replace it. It works perfect now. I had a service man come out and he quoted me $400.00. He told me I needed a whole new ice maker too. Not true. ... Read more I simply email you guys and had the part in 3 days. It only cost me $80.00. I will use your site for every part I need. Thanks