- Home
- KSSC36QTS07
- Instructions
KSSC36QTS07 KitchenAid Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice maker stopped making ice
1 person
found this instruction helpful.
-
John from PHOENIX, AZ
- Easy
- 15 - 30 mins
-
Screw drivers
Followed the instruction video.
Was this helpful?
Thank you for voting!
Replaced Ice maker cover bracket
1 person
found this instruction helpful.
-
Cheryl from FLEMINGTON, NJ
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver
The repair went OK, it is done. It would have been easier if a nut driver was not needed. Plus the location of the nuts was a bit difficult to manage a removal but not impossible.
Was this helpful?
Thank you for voting!
When pushing on ice dispenser paddle in exterior door, there was no sound from motor or auger.
1 person
found this instruction helpful.
-
James from POCATELLO, ID
- Really Easy
- 15 - 30 mins
-
Nutdriver, Socket set
I had to remove ice storage compartment sitting above motor on door to expose auger gear. Then used a small socket to remove 4 screws from underside of auger motor compartment in door. Motor drops out with a small wiring harness attached. This simply unplugs and then swaps in with new motor. Auger axel was sanded to remove rust and grease
... Read more
applied. Motor door and ice compartment were then reattached.
Read less
Was this helpful?
Thank you for voting!
even though there was power inside the plug, the light did not work so a new set of plug was ordered.
1 person
found this instruction helpful.
-
William from DAVIE, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I had watched several video's on installing the plugs in the Kitchenaid model that I had, but when it came down to the install the figuration was a little different. I did figure it out and the rest was a piece of cake. Remember to shut the power off!
Was this helpful?
Thank you for voting!
No ice cubes from the icemaker
1 person
found this instruction helpful.
-
Ronald from Oak Hill, VA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Over the last several years we have had several appliance repairmen try to fix the icemaker. One replaced the entire icemaker. We bought a booster pump for the water. After spending about $1,000 over the past few years trying to fix the problem, a plumber doing routine plumbing work looked at it, and said it might be the control board. I
... Read more
found instructions online how to test the control boards. I ran the test, and they failed. I ordered the parts from PartSelect, followed their easy instructions, and tested the new units. They passed with flying colors. We now actually have an automatic icemaker for the first time in years.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Ice maker quit making ice
1 person
found this instruction helpful.
-
Albert from Milton, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
I took the cover off, and noticed the tabs holding the timer wheel were broken off on one side. after removing the wheel, I noticed the shaft from the ice lifters was broken. Since the only way I could repair it was to buy the entire module, which I did. I received my part in 3 days. When it came, I began removing the old module by takin
... Read more
g out the three screws holding it. After replacing the module which took about 10 minutes, my machine was making ice within about an hour. My ice holder was full in 3 days. Albert Moran, Milton, Fl
Read less
Was this helpful?
Thank you for voting!
Light switch broke
2 of 4 people
found this instruction helpful.
-
Carolee from Spokane Valley, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.
Was this helpful?
Thank you for voting!
Rocker on switch broke off
1 of 2 people
found this instruction helpful.
-
David Barnes from ROSWELL, NM
- Very Easy
- Less than 15 mins
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
Was this helpful?
Thank you for voting!
Filter replacement
1 of 2 people
found this instruction helpful.
-
Thomas from BOTHELL, WA
- Very Easy
- Less than 15 mins
Easily removed old filter and inserted the new one
Was this helpful?
Thank you for voting!
light did not work on the refrigerator side
1 of 2 people
found this instruction helpful.
-
David from GROVESPRING, MO
- Easy
- Less than 15 mins
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what i
... Read more
s inside the refer!
Read less
Was this helpful?
Thank you for voting!
Ice was made intermittently, and then no ice at all!
1 of 2 people
found this instruction helpful.
-
Adam from West Valley City, UT
- Really Easy
- Less than 15 mins
-
Screw drivers
My ice maker about six months ago started to ice make very intermittently and eventually stopped all together. The emiitter no matter what I did was giving me two flashes then a pause, over and over again. I purchased the emitter kit and with a Phillips screwdriver in about five minutes my ice maker kicked the sulinoid on and ice was alre
... Read more
ady started!!! Fast and easy repair!!!
Read less
Was this helpful?
Thank you for voting!
Ice maker on fridge would not make ice.
1 of 2 people
found this instruction helpful.
-
Rod from Jacksonville, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed 4 bottom screws. Removed module screws. Replaced module and motor with new parts (came assembled). Replaced module screws and installed the ice maker with the 4 bottom screws.
Was this helpful?
Thank you for voting!
Light switch broke off
1 of 2 people
found this instruction helpful.
-
Kathy from TEMECULA, CA
- Very Easy
- Less than 15 mins
-
Pliers
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
Was this helpful?
Thank you for voting!
Ice Maker Motor Broke (Plastic Cogs)
1 of 2 people
found this instruction helpful.
-
Robert from Austin, TX
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
1) Turn off the power to the refrigerator 2) Remove the top shelf and ice maker door 3)Remove three hex screws holding the ice maker in place, 4) Unplug the electrical cables and remove the ice maker 5) Remove the plastic cover to the motor module 6) Remove three screws from the motor module and seperate from the housing 7) Remove tw
... Read more
o mounting screws for the motor module 8) Seperate the motor module from the ice tray 9) Remove and replace the plastic ice stripper and rake10) Reassemble in reverse order. Note: Be patient after re-installing the ice maker. It might take an hour or two before its cold enough to kick back on and make ice.
Read less
Was this helpful?
Thank you for voting!
ice maker quit making ice
1 of 2 people
found this instruction helpful.
-
Dale from Mansfield, OH
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench set
I replaced the Electronic control boards because the indicator lights were letting me know that there was a problem, but!!!! when that did not fix the problem, I took the ice maker out and removed the control module from the end of the icemaker only to find out that water had gotten in there and corroded the electronic contacts... this ma
... Read more
y have been why the indicator lights were not working on the emitter and receiver. I was going to purchase just the module, but the entire ice tray was beginning to de-laminate and plastic was flaking off all over. To make a long story somewhat shorter, I purchased a new icemaker and it works fine... one caution though... My icemaker did not come with any information that told me I had to flip the icemaker to the "on" position from vacation mode by inserting a screwdriver in the back of the module inside of a small white ring. This hole is where the shut off arm WOULD go if my model had one.
Read less
Was this helpful?
Thank you for voting!