- Home
- KSSC36QTS07
- Instructions
KSSC36QTS07 KitchenAid Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broke light switch while cleaning
2 of 3 people
found this instruction helpful.
-
Gail from Golden, CO
- Really Easy
- Less than 15 mins
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this helpful?
Thank you for voting!
timing contact wheel was not making reliable contact
2 of 3 people
found this instruction helpful.
-
Robert from Pebble Beach, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Repair was replacing motor kit. I did not use the plastic parts - ejector arm and separator. Went same as others described. I had removed ice maker from refrigerator although this was not necessary to replace motor unit(Please unplug refrigerator whether or not you remove the entire ice maker).
Removed three screws, removed old moto ... Read more r unit, inserted new unit making sure the ice level wire arm end was in slot. Ejector is D shaped so can't go in wrong. Replaced screws and replaced ice maker in freezer. Note - be sure the water tube is in the trough before trying to refasten ice maker.
Added note: If for whatever reason you need to remove ice maker note that there are three mounting screws (others have mentioned this) Completely remove one under middle of ice maker. For the two at top of ice maker - just loosen a few turns. The ice maker can be lifted and pulled away from the wall without removing these screws. Also there is a tab on the electrical wire connector for ice maker at back wall of freezer. Tab must be depressed with a flat tip screw driver while pulling out to remove wire connector. Tab is on wide side of connector facing inside of freezer.
Repair worked. Have lots of ice again.
Removed three screws, removed old moto ... Read more r unit, inserted new unit making sure the ice level wire arm end was in slot. Ejector is D shaped so can't go in wrong. Replaced screws and replaced ice maker in freezer. Note - be sure the water tube is in the trough before trying to refasten ice maker.
Added note: If for whatever reason you need to remove ice maker note that there are three mounting screws (others have mentioned this) Completely remove one under middle of ice maker. For the two at top of ice maker - just loosen a few turns. The ice maker can be lifted and pulled away from the wall without removing these screws. Also there is a tab on the electrical wire connector for ice maker at back wall of freezer. Tab must be depressed with a flat tip screw driver while pulling out to remove wire connector. Tab is on wide side of connector facing inside of freezer.
Repair worked. Have lots of ice again.
Read less
Was this helpful?
Thank you for voting!
No problem
2 of 3 people
found this instruction helpful.
-
Janet from PITTSFORD, NY
- Really Easy
- Less than 15 mins
-
Pliers
I had a son put in the new light bulbs. Rather simple
Was this helpful?
Thank you for voting!
Light over range burned out
3 of 6 people
found this instruction helpful.
-
Vincent from CHICAGO, IL
- Very Easy
- Less than 15 mins
-
Screw drivers
Philips screwdriver
Removed screw (1)
Removed light bulb
Put in new light bulb
Closed door to bulb compartment
Returned screw.
Pro tip! Check how many bulbs you need before ordering. Mine only needed two. I got two. I suspect I’ll buy a new microwave before new bulb burns out again. Ordering/deliv ... Read more ery was fast. No need to have spare on hand.
Removed screw (1)
Removed light bulb
Put in new light bulb
Closed door to bulb compartment
Returned screw.
Pro tip! Check how many bulbs you need before ordering. Mine only needed two. I got two. I suspect I’ll buy a new microwave before new bulb burns out again. Ordering/deliv ... Read more ery was fast. No need to have spare on hand.
Read less
Was this helpful?
Thank you for voting!
No ice
2 of 3 people
found this instruction helpful.
-
Frederick from Rochester Hills, MI
- Easy
- 15 - 30 mins
-
Screw drivers
Go first to Kitchenaid web site and download their consumer services Technical diagnostics on the ice maker. Very well written and clear to follow. Instructions step you through interpretation of blinking code lights which is key to finding the real problem and leads you to repair the correct failed part. My diagnosis said to replace both
... Read more
emitter and receiver. I replaced the emitter first and tried it and solved the problem I didn't need to buy the receiver but I have a spare part now. Do the diagnosis and save yourself some money. PartSelect got the parts to me quickly and saved me money compared to our local parts supply companies.
Read less
Was this helpful?
Thank you for voting!
I broke one tab tht holds to door on
2 of 3 people
found this instruction helpful.
-
Charles from Everett, WA
- Really Easy
- Less than 15 mins
-
Socket set
unscrerwed the broke part and screwed in the new one---5 minutes
Was this helpful?
Thank you for voting!
ice maker quit working
2 of 3 people
found this instruction helpful.
-
Thomas from Hornsby, TN
- Really Easy
- 30 - 60 mins
-
Screw drivers
I was amazed when Fed Ex pulled up to our front door the following day after I ordered the parts, I was wondering what they were delivering and to my amazement it was the parts I had ordered from parts select the previous day , thank you so much , you are awesome. My 73 year old husband who is a 5 year cancer survivor had the part install
... Read more
ed and we were ready to start making ice within 1 hour.He went by the installation information sent in by your customers. Thank you all, Jo Mesplay
Read less
Was this helpful?
Thank you for voting!
Icemaker failed to function
2 of 3 people
found this instruction helpful.
-
Terry from Glendora, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed and disconnected the icemaker, cleaned all areas and disassembled the failed parts. Reassembled with the new parts inlcuded with the purchased package and resinstalled the unit. Started the unit and chedked for proper operation. Successful repair.
Was this helpful?
Thank you for voting!
My ice bucket kept over flowing with cubes
2 of 3 people
found this instruction helpful.
-
Eric from Whittier, CA
- Easy
- 15 - 30 mins
-
Screw drivers
I did some research on the website and found out that there is a test with the sensor lights. When I looked at mine, they were not turning on or blinking when the door was openned.
The repair was very easy to accomplish and all I needed was a small philiips screwdriver. I unscrewed both left and right side panels covering the ... Read more circuit boards and pulled the connector off. I'd say the most diffcult part was lining up the connectors to the boards since there's not a lot of room because of the harness length. Once the boards were connected, they set in place easy and I put the covers back on.
A word of warning, it took the system about ten minutes until the cycle started and water started filling the tray. But aside from that, everything is working perfectly well.
I saved about $200 in service fees!!
The repair was very easy to accomplish and all I needed was a small philiips screwdriver. I unscrewed both left and right side panels covering the ... Read more circuit boards and pulled the connector off. I'd say the most diffcult part was lining up the connectors to the boards since there's not a lot of room because of the harness length. Once the boards were connected, they set in place easy and I put the covers back on.
A word of warning, it took the system about ten minutes until the cycle started and water started filling the tray. But aside from that, everything is working perfectly well.
I saved about $200 in service fees!!
Read less
Was this helpful?
Thank you for voting!
Ice maker stopped making ice
2 of 3 people
found this instruction helpful.
-
Kurt from Noblesville, IN
- Easy
- 15 - 30 mins
-
Screw drivers
The ice maker would not fill with water. Water was available to in-door water dispenser. All signs pointed to the ice maker control boards. Ordered and replaced the boards. Within a couple hours it was making a new batch of ice every 30-60 minutes. The repair instruction video was a great help....made the repair a snap!
Was this helpful?
Thank you for voting!
ice maker would intermittently make ice
1 person
found this instruction helpful.
-
Thomas from ROCHESTER, MN
- Really Easy
- 30 - 60 mins
-
Screw drivers
diagnosed the problem to be the emitter and receiver boards. replaced in about 15 minutes. works like new!
Was this helpful?
Thank you for voting!
Ice maker grinder motor was not running.
1 person
found this instruction helpful.
-
John from DUNNELLON, FL
- Really Easy
- 30 - 60 mins
-
Pliers, Socket set
Remove the ice bucket and check that the auger that turns in the ice bucket is free to turn. Cover the open freezer with cardboard or whatever to retain most of the freezer temperature. Remove the holder that supports the top of the motor shaft. Check the splines on the upper part of the motor shaft and also check the seal under the holde
... Read more
r. Open the access the door to the motor, remove wiring connector and unbolt the motor. Check the lower splines on motor shaft for condition, clean the shaft and apply new grease to the splines. Before installing, connect the wiring to the new motor, push the door switch in, press the ice dispenser arm outside the door to make sure the motor runs. If all ok, check the motor shaft for fit in the new motor. Be careful not to install the motor shaft too deep in the motor splines, otherwise there may not be enough spline showing on the top end to engage the auger. Bolt the motor in place, close access door and install the holder and ice bucket and make sure everything works. If there is not enough spline showing thru the holder to engage the auger, take pliers and pull the shaft up a bit. This seems to be a hit or miss fit on the shaft but you can adjust the height of the shaft without taking every thing apart again. That's all, not difficult at all. But do check parts and pieces for anything else you might need, parts wise, before ordering the motor by itself like I did. Shipping is high, so try to order any associated parts needed when you order the motor. By the way, This site are great to work with!
Read less
Was this helpful?
Thank you for voting!
Recently replaced solenoid for ice maker / water dispenser. Then had problem with filter staying in place and not continually popping out.
1 person
found this instruction helpful.
-
JOHN from BAKERSFIELD, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Watched video of similar model repair for filter housing. But the model KitchenAide refrigerator requires enter and replacing housing from the back. My model has a metal facing which has doors attached to it also. It was simple repair though from the backside of the appliance.
Was this helpful?
Thank you for voting!
Light rocker switch broke and refrigerator light couldn't go on.
2 of 4 people
found this instruction helpful.
-
Cathy from HOPATCONG, NJ
- Very Easy
- Less than 15 mins
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
Was this helpful?
Thank you for voting!
No Problem
1 person
found this instruction helpful.
-
Maria from EL PASO, TX
- Really Easy
- Less than 15 mins
Just needed to replace the water filter
Was this helpful?
Thank you for voting!