KSSC3 KitchenAid Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice dispenser freezing up, dispenser door not closing completely.
22 of 26 people
found this instruction helpful.
-
Robert from Valencia, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
First off, if you have the stainless steel panel inserts on your refrigerator you'll need to remove those to do this repair. I kept looking for the access holes on the underside of the dispenser panel that you're supposed to insert a screwdriver into to pry it off. It wasn't until I removed the freezer door handle, slid the lower stainles
... Read more
s panel insert out, and removed the rail just beneath the dispenser that I could see and access these holes. I also removed the upper stainless panel and rail just above the dispenser to allow enough movement get the dispenser cover off and out. The rest of the repair is pretty straightforward. The old ice door was beaten up and not closing completely, this was letting warm air into the freezer which was melting and re-freezing. This kit fixed the problem.
Read less
Was this helpful?
Thank you for voting!
Ref Side Not Cooling Properly& Noisy
24 of 32 people
found this instruction helpful.
-
DAVID from GRANBURY, TX
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Looked at repair diagram, ordered part [ fast shipping ],first empty freezer pulled everything out removed rear panel, removed motor, installed new motor into housing. Using a heat gun [on low ] defrosted ice build-up on coils, this tookover one hour , reinstalled everything and it started right up but took 24 hours to stablize and get t
... Read more
he ref / freezer back to the -10/37 degree . All better and quiet now. Last time I paid for the repair over $200 very happy thank you part select
Read less
Was this helpful?
Thank you for voting!
water filter needed changed
22 of 26 people
found this instruction helpful.
-
Gerald from Findlay, OH
- Really Easy
- Less than 15 mins
Turned the lock knob on the filter and removed. put
lock knob on new filter and installed.
Very user friendly website, would highly recommend to anyone.
lock knob on new filter and installed.
Very user friendly website, would highly recommend to anyone.
Was this helpful?
Thank you for voting!
The filter needed to be replaced
23 of 30 people
found this instruction helpful.
-
Eva from Arlington, TX
- Really Easy
- Less than 15 mins
Removed the old filter (it screws out) an put the new one in!
Was this helpful?
Thank you for voting!
The auger drum had broken, not allowing any ice cubes to be crushed or dispenses through the door.
22 of 28 people
found this instruction helpful.
-
Evan from Grand Rapids, MI
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Initially I removed the cover to the auger and auger drum. Then the split ring locking washer had to be removed. I used a needle-nosed pliers and small screw-driver to pry that off. The auger arm could then be removed, and the auger blades removed. This proved to be the part that required the most patience. The blades need to removed and
... Read more
returned in their exact pattern. Someone else suggested taking a digital picture of them before removing them; this is a good suggestion that I failed to do. Once the blades are returned, all the other parts can be replaced in reverse order. Put the screws back in, and you are finished.
Read less
Was this helpful?
Thank you for voting!
The old resevoir needed to be replaced
35 of 68 people
found this instruction helpful.
-
Fred from Martinsburg, WV
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
The repair was incredibly easy -
1. Turn off the water at the water line for the fridge
2. Disconnect the pressure fittings for both lines running to the resevoir.
3. Remove the old resevoir
4. Install the new resevoir and run the lines back to the orginal fittings.
5. Reconnect the fittings, turn on water.< ... Read more br />6. Drink water!
1. Turn off the water at the water line for the fridge
2. Disconnect the pressure fittings for both lines running to the resevoir.
3. Remove the old resevoir
4. Install the new resevoir and run the lines back to the orginal fittings.
5. Reconnect the fittings, turn on water.< ... Read more br />6. Drink water!
Read less
Was this helpful?
Thank you for voting!
The outer cap came off and could not turn it.
20 of 23 people
found this instruction helpful.
-
Dennis from Chocowinity, NC
- A Bit Difficult
- 1- 2 hours
Used pliers to help turn knob 1/4 turn to left removed filter; replaced with new filter.
Probably need new outer cap.
Probably need new outer cap.
Was this helpful?
Thank you for voting!
Refrigeator would not drfrost...
27 of 44 people
found this instruction helpful.
-
Curtis from Pikeville, KY
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set, Wrench set
I just removed a few screews and took the cover out of the ice box. Put my voltage meter to the refrigeator and realized the the unit was not defrosting...I then got the part number and entered it in on your web site. A few days later my part arrived. I put the part on and in just about 20 minutes I was up an running again...Thank you
... Read more
Part Select for fast and great service. I own 35 rental properties and having a online appliance parts store really saves me a lot of time and money.
Thank you
Curtis Hall
Thank you
Curtis Hall
Read less
Was this helpful?
Thank you for voting!
ice would not fall from ice maker
22 of 30 people
found this instruction helpful.
-
Greg from Cary, NC
- Really Easy
- 15 - 30 mins
-
Screw drivers
I ran all the ice maker module tests that I could find online, I tried cleaning the contacts inside the ice maker control module, nothing worked...so I finally decided to purchase a new control module. I had already had the module out and taken apart a few times, so the new one was very easy to install. Just removed the entire icemaker
... Read more
from the fridge, removed a few screws, took off the old module, put on the new one, replaced the screws, re-installed the icemaker in the fridge (it just slides in and out similar to a shelf). And 30 minutes later I heard the first batch of ice cubes drop! And by morning the bucket was nearly full. After two weeks of no ice and trying to fix it myself - the family was glad to have ice again (it was July in NC!). In retrospect, I should have followed the advice I found online and ordered the new part sooner and saved all of those frustrating hours of trying to "fix" the part myself.
Read less
Was this helpful?
Thank you for voting!
Refrigerator stop working
23 of 33 people
found this instruction helpful.
-
SAL from UPLAND, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First I removed the relay and over load and exam. Saw that the relay was burnt. Before I order the part I check to see if the compressor was still working by jumping the common start and run terminals.It did. I also checked the start capacitor with a capacitor tester it was good. I than order the part which came the very next day.Installe
... Read more
d the part
Read less
Was this helpful?
Thank you for voting!
Ice maker would not dispense ice
20 of 25 people
found this instruction helpful.
-
William from Victorville, CA
- Easy
- 15 - 30 mins
-
Nutdriver
1. Removed Ice cube bin. 2. Removed the 4 screws holding dispenser bracket in place. 3.Unplugged electrical connector for motor and removed the unit. 4. Removed the coupler,wiring connections and three screws holding dispenser motor to mounting bracket. 5.Installed new dispenser motor onto bracket, put on coupler and connected wiring to m
... Read more
otor. 6. Installed newly assembled unit put ice bin back into place. Dispenser works great.
Read less
Was this helpful?
Thank you for voting!
Clogged Ice shoot in freezer door (curshed ice)
20 of 25 people
found this instruction helpful.
-
Lue from Wichita, KS
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
First remove the ice container from the freezer
and dump all of the ice. Remove the four
screws holding the front ice container cover. Remove the control arm screw and bracket from the bottom of the ice container, remove crusher housing (screws and retainer clip). Remove nylon
bearing nut on front of auger shaft (left ha ... Read more nded threads). Remove crusher blades and spacers (remember order of blades and spacers). Remove broken floating baffle. Replace baffle and reverse removal procedures.
and dump all of the ice. Remove the four
screws holding the front ice container cover. Remove the control arm screw and bracket from the bottom of the ice container, remove crusher housing (screws and retainer clip). Remove nylon
bearing nut on front of auger shaft (left ha ... Read more nded threads). Remove crusher blades and spacers (remember order of blades and spacers). Remove broken floating baffle. Replace baffle and reverse removal procedures.
Read less
Was this helpful?
Thank you for voting!
Over flowing Icemaker
21 of 29 people
found this instruction helpful.
-
Thomas from Flower Mound, TX
- Really Easy
- Less than 15 mins
-
Nutdriver
Ice Maker would seem like it was the valve was leaking and Ice would build up at the rear of tray.
After listening to it cycle, (drop ice and fill) valve would open up again about 20 minutes later.
Over flowed and iceberg would form at rear.
Replaced icemaker unit and works fine now.
After listening to it cycle, (drop ice and fill) valve would open up again about 20 minutes later.
Over flowed and iceberg would form at rear.
Replaced icemaker unit and works fine now.
Was this helpful?
Thank you for voting!
Ice machine wouldn't dispense ice from the door.
20 of 26 people
found this instruction helpful.
-
Linda from Jackson, MS
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the broken coupling with the new one from your store. It took less than 10 minutes. The video you provided on the website was very helpful.
Other Parts Used:
Was this helpful?
Thank you for voting!
Ice maker stopped working.
22 of 32 people
found this instruction helpful.
-
Scott from Fort Lauderdale, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed the icemaker to see if I could determine problem; motor was seized; got part numbers and ordered from you; parts arrived next day (even though overnight delivery wasnt' requested - so THANK YOU!); compared new parts to original to be sure of fit; reassembled unit; reinstalled in freezer, and waited for the sound of water filling t
... Read more
he tray. Producing like brand new again! Cancelled the service call w/ Sears for the following week (when it was convenient for them) Loved your service!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!