KSM85 Mixer - Instructions

Looked for the probable cause from a U-tube video, then found the parts list and repair video on the PartSelect website. When the parts arrived within 3days the shipped email had a video on exactly how to complete the repair. Repair video was very well done and easy to follow.

Looked at the mixer schematic form your website,which made it easy for me to take it apart. Once it was apart & all the grease removed I disassembled & cleaned all the drive parts. Saw what was warn, ordered the parts from you. Three days later received the parts, everything fit perfect. Added grease,assembled the mixer and it ran perfect ... Read more , good for another 20 yrs. Thank you for making it so easy to repair an old mixer in just over two hours. Rolf

Replace went good used the online video, my husband doesn't usually use any help but said the video helped him. Now my mixer works perfect. Also the price and shipping time was awesome.

Repairing/replacing worm-gear (FSP part# W10112253) for a KitchenAid Stand Mixer model number K5SS. First: I am writing this story because all the videos or repair articles I’ve viewed are either misleading or incorrect in that they do not include older K5SS models. 1. These older models from the mid 1960’s or even earlier have four very ... Read more large #4 chrome plated Phillips Head Screws holding the mixer base to the motor assembly and NOT four small machine screws (one with a lock-washer) as seen on other repair videos. In addition, the stand is composed of two separate pieces with the bottom half being held together with another four identical #4 chrome plated Phillips Head Screws. The upper four holding the stand to the motor housing (I used a manual impact driver to loosen the very stubborn, #4 Phillips screws) must be removed so as to access the four smaller Phillips machine screws (no lock-washers found here, best buy at least four #10, split, before reassembly) 2. Lastly, you will need two pin punches however the recommended smaller 3/32 inch is still too large to remove the pin in the tower assembly. You will need one size smaller or a #4 pin punch instead. These older Kitchen Aid mixers were built with very tight tolerances. Please be patient and take your time removing the pins. Good Luck……. Jim

Got the right parts, very quick delivery, will use again.

I removed the pin from the outside shaft,then removed all screw around the body of the mixer,then removed the top case out,took 3 screws out from the the gear assembly case......punched the pin out of worm gear then release the little shaft out from the case,replaced a new one....then starting go backward till completely all assembled d ... Read more on't forget lube grease to all gears and test run good very smooth.........it's ok

I just thought there had to be a way to replace a component to correct the speed problem. I've never worked on a mixer before, so I thought it would be a challenge. Actually the repair was fairly easy. Make sure the unit is unplugged from AC. I removed the back motor cover with one screw and removed the end seal. I compared the parts ... Read more on the mixer with the diagram provided at the Part Select website. I then ordered the parts. When the parts arrived 3 days later, I removed the Speed Control Plate ( 3 screws) and Phase Control Bd (1 screw) as one Assy. Removed the old Governor and slipped on the new one. Assy the new Speed Control Plate and Phase Control Bd comparing wiring and screwed them back to the unit. Removed the two motor bushes by unscrewing the side black motor brush holders and inserting the new brushes. I tried powering motor and nothing happened. I thought, great, now what did I do? I found out that you must make sure the brushes actually touch the armature otherwise the motor doesn't run. The gears are worn from grinding to much deer meat and my wife says no more. I've ordered new gears and looks like that job, too, will be easy to repair. Adding these parts is alot cheaper than buying a new unit and it will run like new. Not bad for over 10 years of usage.

Skewer the screw in with my fingers,

Used the diagram on the website and a video
Totally worked!

Unscrewed old Screw Cap, tapped it out with hammer. Replaced with new screw cap that was slightly different and tight. Tapped it in with piece of wood over it and hammered it on. No problems.

I removed the spring loaded brush screw on the side of my mixer and lost it the next day. I found a schematic of this part on your website and ordered the four pieces that make up the brush screw(?). They arrived in just a few days and I referred back to the schematic to put it together. I then popped it in my mixer, screwed it down, plug ... Read more ged her in and away we go! Easiest repair I’ve ever done! I’m a 70 year old retired lady and not very handy, but this was an easy fix! Thank you, PartSelect!

The repair was easy only requiring a phillips head screw driver to remove the old screw cap. The new screw cap fit snuggly and required a little downward pressure from my hand to seat it. Then I simply tightened the screws. Good as new for this 30+ year old mixer. My wife loves this mixer that was given to her by her Aunt. Glad we co ... Read more uld keep it going.

I removed three screws, pulled off the old base plate.
Put new base plate in place and replaced the screws

I removed one screw on back, once inside mixer I removed the ground screw then pulled off the black and white push on caps, then I reversed everything to get it installed, very easy

Just put on the new whip...exactly like old one.